Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800  Short in D Squib Circuit  B1801  Open in D Squib Circuit  B1802  Short in D Squib Circuit (to Ground)  B1803  Short in D Squib Circuit (to +B)  


DESCRIPTION

The driver side squib circuit consists of the airbag ECU assembly, spiral cable sub-assembly and horn button assembly.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.


DTC No. DTC Detection Condition Trouble Area
B1800
·

The airbag ECU assembly receives a line short circuit signal in the driver side squib circuit during primary check.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly (Driver side squib)

·

Airbag ECU assembly


B1801
·

The airbag ECU assembly receives an open circuit signal in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


B1802
·

The airbag ECU assembly receives a short circuit to ground signal in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


B1803
·

The airbag ECU assembly receives a short circuit to B+ signal in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C370787E01
0.688,2.542 2.063,2.74 1.375,0.198 10 false z6*1,z7*2 0.688,2.74 2.135,3.188 1.448,0.448 10 false Horn Button Assembly (Driver Side Squib) 0.375,3.344 1.75,3.542 1.375,0.198 10 false *1: w/o Dual Airbag 1.833,3.354 3.208,3.552 1.375,0.198 10 false *2: w/ Dual Airbag 2.135,1.042 2.354,1.281 0.219,0.24 10 false D+ 2.156,1.885 2.375,2.125 0.219,0.24 10 false D- 2.396,0.906 2.646,1.25 0.25,0.344 10 false 1*1 2*2 2.396,1.74 2.646,2.083 0.25,0.344 10 false 2*1 1*2 3.5,0.906 3.75,1.25 0.25,0.344 10 false 3*1 2*2 3.51,1.729 3.76,2.073 0.25,0.344 10 false 4*1 1*2 3.25,1.042 3.469,1.281 0.219,0.24 10 false D+ 3.271,1.885 3.49,2.125 0.219,0.24 10 false D- 2.688,2.531 3.042,2.708 0.354,0.177 10 false D52 2.677,2.719 3.583,3.125 0.906,0.406 10 false Spiral Cable Sub-assembly 4.51,1.052 4.729,1.292 0.219,0.24 10 false 5 4.521,1.896 4.74,2.135 0.219,0.24 10 false 6 4.719,1.156 4.938,1.396 0.219,0.24 10 false D+ 4.719,1.979 4.938,2.219 0.219,0.24 10 false D- 4.823,3.042 5.177,3.219 0.354,0.177 10 false D27 4.833,3.219 6.375,3.594 1.542,0.375 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241740E01
0.205,1.342 0.361,1.494 0.156,0.152 10 *1 1.03,0.798 1.197,0.963 0.167,0.165 10 *2 2.698,1.106 2.873,1.262 0.174,0.156 10 *3 1.902,1.342 2.055,1.494 0.153,0.151 10 *4 2.368,0.798 2.484,0.951 0.117,0.153 10 A 2.102,0.798 2.219,0.951 0.117,0.153 10 B 1.754,0.798 1.881,0.951 0.127,0.153 10 C 1.492,0.798 1.619,0.951 0.127,0.153 10 D 0.641,0.798 0.768,0.951 0.127,0.153 10 E 0.389,0.798 0.516,0.951 0.127,0.153 10 F 1.988,0.947 1.988,1.336 false 0.287,0.947 0.287,1.336 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable sub-assembly connector (on the horn button assembly side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire



OK

2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB)

NG

REPLACE WIRE HARNESS

2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB)
a.
U190384E02
0.313,0.802 0.313,0.563 false 1.729,2.708 1.51,2.708 false 1.948,2.271 1.75,2.271 false 0.313,1.688 0.479,1.865 0.167,0.177 10 false *a 0.458,1.917 0.667,2.115 0.208,0.198 10 false *A 0.458,2.469 0.625,2.646 0.167,0.177 10 false *B 1.781,2.625 1.948,2.823 0.167,0.198 10 false *b 0.24,0.823 0.448,1.063 0.208,0.24 10 false *1 1.146,0.406 1.344,0.646 0.198,0.24 10 false *2 2.698,0.719 2.906,0.948 0.208,0.229 10 false *3 2,2.188 2.313,2.385 0.313,0.198 10 false SST 2.344,0.417 2.458,0.552 0.115,0.135 10 false A 2.177,0.406 2.302,0.625 0.125,0.219 10 false B 1.75,0.406 1.875,0.625 0.125,0.219 10 false C 1.594,0.406 1.719,0.615 0.125,0.208 10 false D 0.75,0.406 0.865,0.542 0.115,0.135 10 false E 0.438,0.406 0.573,0.583 0.135,0.177 10 false F 0.458,2.146 0.625,2.302 0.167,0.156 10 false z6 0.469,2.688 0.646,2.875 0.177,0.188 10 false z7

Connect the instrument panel wire to the airbag ECU assembly and spiral cable sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the horn button assembly (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTCs B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*A w/o Dual Airbag
*B w/ Dual Airbag
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Orange



OK

NG

3.CHECK DRIVER SIDE SQUIB CIRCUIT
3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
U190348E02
0.313,0.792 0.313,0.521 false 1.875,2.385 1.573,2.385 false 0.229,0.833 0.448,1.083 0.219,0.25 10 false *1 1.146,0.354 1.375,0.625 0.229,0.271 10 false *2 2.823,0.625 3.021,0.875 0.198,0.25 10 false *3 2.521,0.344 2.667,0.563 0.146,0.219 10 false A 2.208,0.354 2.375,0.583 0.167,0.229 10 false B 1.75,0.354 1.854,0.552 0.104,0.198 10 false C 1.604,0.354 1.74,0.552 0.135,0.198 10 false D 0.76,0.365 0.875,0.5 0.115,0.135 10 false E 0.448,0.365 0.552,0.5 0.104,0.135 10 false F 1.906,2.292 2.135,2.51 0.229,0.219 10 false *b 0.26,1.635 0.469,1.917 0.208,0.281 10 false *a 0.479,2.083 0.646,2.24 0.167,0.156 10 false z6 0.479,2.51 0.646,2.667 0.167,0.156 10 false z7 0.844,2.083 1.01,2.24 0.167,0.156 10 false *A 0.854,2.5 1.021,2.656 0.167,0.156 10 false *B

Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
z6-2 (D-) - Body ground Ignition switch ON Below 1 V
z6-1 (D+) - Body ground Ignition switch ON Below 1 V


Standard Voltage:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
z7-2 (D+) - Body ground Ignition switch ON Below 1 V
z7-1 (D-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
z6-2 (D-) - z6-1 (D+) Always Below 1 Ω


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
z7-2 (D+) - z7-1 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
z6-2 (D-) - Body ground Always 1 MΩ or higher
z6-1 (D+) - Body ground Always 1 MΩ or higher


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
z7-2 (D+) - Body ground Always 1 MΩ or higher
z7-1 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
z6-2 (D-) - z6-1 (D+) Always 1 MΩ or higher


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
z7-2 (D+) - z7-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*A w/o Dual Airbag
*B w/ Dual Airbag
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Orange




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238229E01
0.366,1.282 0.522,1.433 0.156,0.152 10 *1 1.083,0.731 1.251,0.896 0.167,0.165 10 *2 2.618,1.008 2.792,1.164 0.174,0.156 10 *3 2.305,0.731 2.421,0.884 0.117,0.153 10 A 2.145,0.731 2.261,0.884 0.117,0.153 10 B 1.694,0.731 1.821,0.884 0.127,0.153 10 C 1.531,0.731 1.658,0.884 0.127,0.153 10 D 0.704,0.731 0.831,0.884 0.127,0.153 10 E 0.55,0.731 0.677,0.884 0.127,0.153 10 F 0.449,0.88 0.449,1.269 false

Connect the connectors to the horn button assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTCs B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire from the spiral cable sub-assembly.


U147000E02
0.219,0.698 0.219,0.99 false 2.094,0.542 2.094,0.208 2.094,0.208 1.927,0.208 false 1.24,2.344 1.51,2.49 0.271,0.146 10 false D52 0.344,0.521 0.448,0.677 0.104,0.156 10 false F 0.667,0.51 0.792,0.667 0.125,0.156 10 false E 1.49,0.521 1.615,0.677 0.125,0.156 10 false D 1.802,0.521 1.927,0.677 0.125,0.156 10 false C 2.25,0.521 2.375,0.677 0.125,0.156 10 false B 2.573,0.521 2.698,0.677 0.125,0.156 10 false A 1.031,0.51 1.208,0.688 0.177,0.177 10 false *2 0.146,1.01 0.302,1.188 0.156,0.177 10 false *1 2.823,0.833 3,0.979 0.177,0.146 10 false *3 1.031,1.615 1.208,1.781 0.177,0.167 10 false *a 1.74,0.135 1.896,0.281 0.156,0.146 10 false *4

b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
D52-3 (D+) - Body ground Ignition switch ON Below 1 V
D52-4 (D-) - Body ground Ignition switch ON Below 1 V


Standard Voltage:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
D52-1 (D-) - Body ground Ignition switch ON Below 1 V
D52-2 (D+) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
D52-3 (D+) - D52-4 (D-) Always Below 1 Ω


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
D52-1 (D-) - D52-2 (D+) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
D52-3 (D+) - Body ground Always 1 MΩ or higher
D52-4 (D-) - Body ground Always 1 MΩ or higher


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
D52-1 (D-) - Body ground Always 1 MΩ or higher
D52-2 (D+) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
D52-3 (D+) - D52-4(D-) Always 1 MΩ or higher


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
D52-1 (D-) - D52-2 (D+) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)




OK

6.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK SPIRAL CABLE SUB-ASSEMBLY
a.
U190349E02
0.375,0.969 0.375,0.74 false 2.083,0.969 2.083,0.698 false 1.885,2.375 1.583,2.375 false 0.292,0.99 0.5,1.229 0.208,0.24 10 false *1 1.042,0.531 1.25,0.76 0.208,0.229 10 false *2 2,0.99 2.188,1.198 0.188,0.208 10 false *4 2.885,0.813 3.073,1.052 0.188,0.24 10 false *3 0.271,1.625 0.531,1.917 0.26,0.292 10 false *a 1.927,2.281 2.125,2.5 0.198,0.219 10 false *b 0.417,2.094 0.583,2.25 0.167,0.156 10 false z6 0.427,2.531 0.594,2.688 0.167,0.156 10 false z7 0.823,2.115 0.99,2.271 0.167,0.156 10 false *A 0.833,2.552 1,2.708 0.167,0.156 10 false *B 2.573,0.531 2.708,0.76 0.135,0.229 10 false A 2.26,0.531 2.406,0.719 0.146,0.188 10 false B 1.802,0.531 1.938,0.74 0.135,0.208 10 false C 1.5,0.531 1.635,0.76 0.135,0.229 10 false D 0.656,0.542 0.771,0.677 0.115,0.135 10 false E 0.344,0.542 0.448,0.677 0.104,0.135 10 false F

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
z6-2 (D-) - Body ground Ignition switch ON Below 1 V
z6-1 (D+) - Body ground Ignition switch ON Below 1 V


Standard Voltage:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
z7-2 (D+) - Body ground Ignition switch ON Below 1 V
z7-1 (D-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
z6-2 (D-) - z6-1 (D+) Always Below 1 Ω


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
z7-2 (D+) - z7-1 (D-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
z6-2 (D-) - Body ground Always 1 MΩ or higher
z6-1 (D+) - Body ground Always 1 MΩ or higher


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
z7-2 (D+) - Body ground Always 1 MΩ or higher
z7-1 (D-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Dual Airbag:
Tester Connection Condition Specified Condition
z6-2 (D-) - z6-1 (D+) Always 1 MΩ or higher


Standard Resistance:
w/ Dual Airbag:
Tester Connection Condition Specified Condition
z7-2 (D+) - z7-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.

Text in Illustration
*A w/o Dual Airbag
*B w/ Dual Airbag
*1 Horn Button Assembly
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Orange




OK

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY