The driver side squib 2nd step circuit consists of the airbag ECU assembly, spiral cable sub-assembly and horn button assembly.
The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1810 | ·
The airbag ECU assembly receives a line short circuit signal in the driver side squib 2nd step circuit during primary check. ·
Spiral cable sub-assembly malfunction ·
Driver side squib 2nd step malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Horn button assembly (Driver side squib 2nd step) ·
Airbag ECU assembly |
| B1811 | ·
The airbag ECU assembly receives an open circuit signal in the driver side squib 2nd step circuit. ·
Spiral cable sub-assembly malfunction ·
Driver side squib 2nd step malfunction ·
Airbag ECU assembly malfunction |
|
| B1812 | ·
The airbag ECU assembly receives a short circuit to ground signal in the driver side squib 2nd step circuit. ·
Spiral cable sub-assembly malfunction ·
Driver side squib 2nd step malfunction ·
Airbag ECU assembly malfunction |
|
| B1813 | ·
The airbag ECU assembly receives a short circuit to B+ signal in the driver side squib 2nd step circuit. ·
Spiral cable sub-assembly malfunction ·
Driver side squib 2nd step malfunction ·
Airbag ECU assembly malfunction |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
Check that the spiral cable sub-assembly connector (on the horn button assembly side) is not damaged.
The lock button is not disengaged, or the claw of the lock is not deformed or damaged.
Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.
The short springs are not deformed or damaged.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *4 | Instrument Panel Wire |
OK
NG
Connect the instrument panel wire to the airbag ECU assembly and spiral cable sub-assembly.
Connect SST (resistance 2.1 Ω) to connector E (black connector).
Never connect the tester to the horn button assembly (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1810, B1811, B1812 or B1813 is not output.
Codes other than DTCs B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect SST from connector E.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Horn Button Assembly) |
| *b | Color: Black |
OK
NG
Disconnect the instrument panel wire from the airbag ECU assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-1 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| z6-2 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-1 (D2+) - z6-2 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-1 (D2+) - Body ground | Always | 1 MΩ or higher |
| z6-2 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-1 (D2+) - z6-2 (D2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Horn Button Assembly) |
| *b | Color: Black |
OK
NG
Connect the connectors to the horn button assembly and airbag ECU assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1810, B1811, B1812 or B1813 is not output.
Codes other than DTCs B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the instrument panel wire from spiral cable sub-assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D52-3 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| D52-4 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D52-3 (D2+) - D52-4 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D52-3 (D2+) - Body ground | Always | 1 MΩ or higher |
| D52-4 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D52-3 (D2+) - D52-4 (D2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
OK
NG
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-1 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| z6-2 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-1 (D2+) - z6-2 (D2-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-1 (D2+) - Body ground | Always | 1 MΩ or higher |
| z6-2 (D2-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-1 (D2+) - z6-2 (D2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
| *1 | Horn Button Assembly |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Horn Button Assembly) |
| *b | Color: Black |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG