Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297704 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1835  Short in Curtain Shield Airbag (LH) Squib Circuit  B1836  Open in Curtain Shield Airbag (LH) Squib Circuit  B1837  Short in Curtain Shield Airbag (LH) Squib Circuit (to Ground)  B1838  Short in Curtain Shield Airbag (LH) Squib Circuit (to +B)  


DESCRIPTION

The curtain shield squib LH circuit consists of the airbag ECU assembly and curtain shield airbag assembly LH.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1835
·

The airbag ECU assembly receives a line short circuit signal in the curtain shield squib LH circuit during primary check.

·

Curtain shield squib LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Airbag ECU assembly


B1836
·

The airbag ECU assembly receives an open circuit signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag ECU assembly malfunction


B1837
·

The airbag ECU assembly receives a short circuit to ground signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag ECU assembly malfunction


B1838
·

The airbag ECU assembly receives a short circuit to B+ signal in the curtain shield squib LH circuit.

·

Curtain shield squib LH malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C263726E04
0.432,2.614 0.729,2.751 0.297,0.137 10 H30 4.831,3.02 5.105,3.158 0.273,0.137 10 H17 0.418,2.764 2.643,3.086 2.225,0.323 10 Curtain Shield Airbag Assembly LH (Curtain Shield Squib LH) 4.817,3.17 6.209,3.316 1.391,0.147 10 Airbag ECU Assembly 2.414,1.069 2.509,1.209 0.096,0.140 10 1 2.414,1.905 2.514,2.045 0.100,0.140 10 2 4.718,1.17 5.061,1.309 0.343,0.139 10 ICL+ 4.718,2.01 5.022,2.149 0.304,0.139 10 ICL- 1.977,1.069 2.319,1.208 0.343,0.139 10 ICL+ 2.016,1.905 2.320,2.044 0.304,0.139 10 ICL- 4.528,1.069 4.623,1.209 0.096,0.140 10 7 4.529,1.905 4.623,2.045 0.094,0.140 10 6

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241752E01
0.637,0.972 0.758,1.125 0.121,0.153 10 D 1.044,0.972 1.164,1.125 0.121,0.153 10 C 1.622,0.972 1.743,1.125 0.121,0.153 10 B 2.025,0.972 2.146,1.125 0.121,0.153 10 A 2.47,0.979 2.646,1.154 0.177,0.175 10 *2 0.45,1.577 0.602,1.730 0.152,0.152 10 *1 0.526,1.119 0.526,1.56 false 1.638,0.473 1.790,0.625 0.152,0.152 10 *3 1.387,0.987 1.387,0.563 1.387,0.563 1.613,0.563 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the curtain shield airbag assembly LH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the curtain shield airbag assembly LH and airbag ECU assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the curtain shield airbag assembly LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Curtain Shield Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire



OK

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)
a.
U147017E02
1.802,2.313 1.99,2.313 false 0.698,0.885 0.698,1.24 false 0.823,0.74 0.948,0.896 0.125,0.156 10 false D 1.125,0.74 1.25,0.896 0.125,0.156 10 false C 1.635,0.729 1.76,0.885 0.125,0.156 10 false B 1.802,0.729 1.927,0.885 0.125,0.156 10 false A 2.229,0.708 2.406,0.885 0.177,0.177 10 false *2 0.635,1.281 0.792,1.458 0.156,0.177 10 false *1 0.417,1.771 0.594,1.938 0.177,0.167 10 false *a 2.031,2.24 2.323,2.396 0.292,0.156 10 false SST 0.448,2.354 0.719,2.5 0.271,0.146 10 false H30

Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag assembly LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTCs B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Curtain Shield Airbag Assembly LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly LH)



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
U147018E02
0.615,0.948 0.615,1.396 false 1.375,0.823 1.375,0.438 1.375,0.438 1.531,0.438 false 1.021,3.031 1.417,2.354 true 1.573,2.344 1.958,3.021 true 0.625,2.427 0.896,2.573 0.271,0.146 10 false H30 0.719,0.802 0.844,0.958 0.125,0.156 10 false D 1.083,0.802 1.208,0.958 0.125,0.156 10 false C 1.583,0.802 1.708,0.958 0.125,0.156 10 false B 1.948,0.802 2.073,0.958 0.125,0.156 10 false A 2.365,0.802 2.542,0.979 0.177,0.177 10 false *2 0.521,1.417 0.677,1.594 0.156,0.177 10 false *1 0.313,1.865 0.49,2.031 0.177,0.167 10 false *a 1.552,0.354 1.708,0.531 0.156,0.177 10 false *3 0.719,2.969 1.021,3.198 0.302,0.229 10 false ICL+ 2.01,2.969 2.323,3.198 0.313,0.229 10 false ICL-

Disconnect the floor wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H30-1 (ICL+) - Body ground Ignition switch ON Below 1 V
H30-2 (ICL-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H30-1 (ICL+) - H30-2 (ICL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H30-1 (ICL+) - Body ground Always 1 MΩ or higher
H30-2 (ICL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H30-1 (ICL+) - H30-2 (ICL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Curtain Shield Airbag Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly LH)




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238245E01
0.762,1.589 0.918,1.740 0.156,0.152 10 *1 2.147,0.987 2.322,1.143 0.174,0.156 10 *2 1.73,0.987 1.847,1.140 0.117,0.153 10 A 1.572,0.987 1.689,1.140 0.117,0.153 10 B 1.119,0.987 1.246,1.140 0.127,0.153 10 C 0.962,0.987 1.089,1.140 0.127,0.153 10 D 0.845,1.142 0.845,1.575 false

Connect the connectors to the curtain shield airbag assembly LH and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTCs B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Curtain Shield Airbag Assembly LH
*2 Airbag ECU Assembly



OK

NG