Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2012.03–2016.06
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297706 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B593380E03
0.927,1.323 1.5,1.323 true 4.958,1.24 4.958,0.719 4.958,0.719 4.531,0.719 true 4.323,1.302 4.896,1.302 true 0.583,1.417 1.531,1.417 true 2,2.25 2,2.083 true 5.406,2.25 5.406,2.083 true 2.188,2.188 2.021,2.021 true 5.583,2.167 5.417,2 true 0.635,0.167 0.969,0.49 0.333,0.323 12 false *A 4.01,0.167 4.417,0.521 0.406,0.354 12 false *B 0.76,1.229 1.073,1.385 0.313,0.156 10 false *a 0.396,1.323 0.708,1.479 0.313,0.156 10 false *c 4.344,0.635 4.656,0.792 0.313,0.156 10 false *d 4.146,1.208 4.458,1.365 0.313,0.156 10 false *a 1.938,2.271 2.115,2.448 0.177,0.177 10 false *b 2.177,2.177 2.354,2.354 0.177,0.177 10 false *b 5.323,2.25 5.5,2.427 0.177,0.177 10 true *b 5.594,2.156 5.771,2.333 0.177,0.177 10 true *b

Text in Illustration
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn


b.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

When rotating the spiral cable sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B450368E01
1.719,1.938 1.719,1.292 true 1.635,1.969 1.948,2.125 0.313,0.156 10 false *a

While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

Text in Illustration
*a Interlock
V113147

Counterclockwise

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


HINT:

The interlock operates at the top and bottom of the connector.



ii.
B453377

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B450359E01
1.927,1.177 2.813,1.177 true 2.854,1.094 3.167,1.25 0.313,0.156 10 false *a

While pushing on the interlock, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

Text in Illustration
*a Interlock
V113147

Clockwise

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



iv.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B593380E03
0.927,1.323 1.5,1.323 true 4.958,1.24 4.958,0.719 4.958,0.719 4.531,0.719 true 4.323,1.302 4.896,1.302 true 0.583,1.417 1.531,1.417 true 2,2.25 2,2.083 true 5.406,2.25 5.406,2.083 true 2.188,2.188 2.021,2.021 true 5.583,2.167 5.417,2 true 0.635,0.167 0.969,0.49 0.333,0.323 12 false *A 4.01,0.167 4.417,0.521 0.406,0.354 12 false *B 0.76,1.229 1.073,1.385 0.313,0.156 10 false *a 0.396,1.323 0.708,1.479 0.313,0.156 10 false *c 4.344,0.635 4.656,0.792 0.313,0.156 10 false *d 4.146,1.208 4.458,1.365 0.313,0.156 10 false *a 1.938,2.271 2.115,2.448 0.177,0.177 10 false *b 2.177,2.177 2.354,2.354 0.177,0.177 10 false *b 5.323,2.25 5.5,2.427 0.177,0.177 10 true *b 5.594,2.156 5.771,2.333 0.177,0.177 10 true *b

Text in Illustration
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn

NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 2.INSTALL SPIRAL CABLE SUB-ASSEMBLY

a.
B558545E01
1.719,1.323 2.708,0.635 2.708,0.635 1.729,0.635 true 2.76,0.573 3.219,0.948 0.458,0.375 10 false *a

Apply grease to the protrusions on the steering sensor.

Text in Illustration
*a Protrusion

NOTICE:
·

Do not rotate the steering sensor.

·

Apply the specified grease supplied with a new steering sensor.




b.
B313958E02
2.094,0.25 2.438,0.667 true 2.073,1.01 2.438,1.156 true 0.771,0.854 1.354,0.5 true 2.917,0.927 3.177,0.688 true 1.927,0.115 2.104,0.344 0.177,0.229 10 false *1 3.198,0.573 3.385,0.729 0.188,0.156 10 false *2 1.396,0.385 1.583,0.542 0.188,0.156 10 false *2 1.917,0.917 2.104,1.073 0.188,0.156 10 false *1

Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.

Text in Illustration
*1 Guide
*2 Pin

NOTICE:

Do not rotate the steering sensor until the spiral cable has been attached to it.



Hide 3. ALIGN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 4.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable sub-assembly without the steering wheel with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



c.

Check that the front wheels are facing straight ahead.


d.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch pin may snap.



e.

Engage the 3 claws to install the spiral cable with sensor sub-assembly.


f.

Connect the each connector.


Hide 45286 5.INSTALL UPPER STEERING COLUMN COVER

Hide 45289A 7.INSTALL STEERING COLUMN COVER SUPPORT (w/ Entry and Start System)

Hide 55422 8.INSTALL UPPER INSTRUMENT PANEL METER ORNAMENT

Hide 55405B 10.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 73900 11.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (w/ Knee Airbag)

Hide 55606 12.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55318C 13.INSTALL INSTRUMENT SIDE PANEL (w/o Knee Airbag)

Hide 14.ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B450360E03
4.135,2.396 4.135,1.688 true 4.177,1.51 4.177,1.26 4.177,1.26 3.542,1.26 true 0.74,2.406 0.74,1.854 true 0.75,1.604 0.76,1.385 0.76,1.385 0.229,1.385 true 0.188,0.083 0.5,0.333 0.313,0.25 12 false *A 3.833,0.083 4.167,0.333 0.333,0.25 12 false *B 0.052,1.271 0.365,1.427 0.313,0.156 10 false *a 0.646,2.427 0.823,2.615 0.177,0.188 10 false *b 4.073,2.396 4.385,2.552 0.313,0.156 10 false *c 3.354,1.156 3.667,1.313 0.313,0.156 10 false *a

Text in Illustration
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Colored Roller
*c Top of Flat Cable U-turn - -


d.

If the spiral cable with sensor sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable with sensor sub-assembly.

·

When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B428424E01
0.552,0.958 1.604,0.958 true 0.333,0.813 0.646,0.969 0.313,0.156 10 false *a

While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

Text in Illustration
*a Interlock
V113147

Counterclockwise

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



ii.
B450361

If the spiral cable with sensor sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B450362E01
2.729,1.76 1.813,0.99 true 2.781,1.708 3.094,1.865 0.313,0.156 10 false *a

While pushing on the interlock, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

Text in Illustration
*a Interlock
V113147

Clockwise

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



iv.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B450360E03
4.135,2.396 4.135,1.688 true 4.177,1.51 4.177,1.26 4.177,1.26 3.542,1.26 true 0.74,2.406 0.74,1.854 true 0.75,1.604 0.76,1.385 0.76,1.385 0.229,1.385 true 0.188,0.083 0.5,0.333 0.313,0.25 12 false *A 3.833,0.083 4.167,0.333 0.333,0.25 12 false *B 0.052,1.271 0.365,1.427 0.313,0.156 10 false *a 0.646,2.427 0.823,2.615 0.177,0.188 10 false *b 4.073,2.396 4.385,2.552 0.313,0.156 10 false *c 3.354,1.156 3.667,1.313 0.313,0.156 10 false *a

Text in Illustration
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type)
*a Check Window *b Colored Roller
*c Top of Flat Cable U-turn - -

NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 45111 15.INSTALL STEERING WHEEL ASSEMBLY