Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2012.03–2016.06
RM2090E _58 Vehicle Interior _060701 SUPPLEMENTAL RESTRAINT SYSTEMS _0297706 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



a.

Remove the spiral cable with sensor sub-assembly from the vehicle.

(See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL)


b.

Visually check for defects with the spiral cable sub-assembly.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable sub-assembly with a new one.



c.

Check the spiral cable sub-assembly.

U190231E02
0.688,0.896 0.969,1.104 0.281,0.208 10 false *A 0.115,0.083 0.396,0.292 0.281,0.208 10 false *a 0.615,1.708 0.896,1.917 0.281,0.208 10 false *b 1.052,1.708 1.333,1.917 0.281,0.208 10 false *c 4.073,0.896 4.354,1.104 0.281,0.208 10 false *B 2.25,1.052 2.427,1.208 0.177,0.156 10 false z5 1.094,2.052 1.271,2.208 0.177,0.156 10 false z6 4.24,2.063 4.417,2.219 0.177,0.156 10 false z6 0.646,2.063 0.823,2.219 0.177,0.156 10 false z7 1.427,4.177 1.729,4.333 0.302,0.156 10 false D51 2.521,4.396 2.823,4.552 0.302,0.156 10 false D52 2.823,1.052 3,1.208 0.177,0.156 10 false z4 5.458,1.052 5.635,1.208 0.177,0.156 10 false z5 4.646,4.167 4.948,4.323 0.302,0.156 10 false D51 5.729,4.385 6.031,4.542 0.302,0.156 10 false D52 6.031,1.042 6.208,1.198 0.177,0.156 10 false z4

Text in Illustration
*A for Dual Airbag System *B for Single Airbag System
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Color: Orange
*c Color: Black - -

i.

Set the spiral cable sub-assembly to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.

Standard Resistance:
for Dual Airbag System:
Tester Connection Condition Specified Condition
D51-1 - z4-3 Always 3 Ω or less
D51-2 - z4-4 Always 3 Ω or less
D51-2 - z5-6 Always 3 Ω or less
D51-8 - z4-2 Always 3 Ω or less
D51-8 - z5-1 Always 3 Ω or less
D51-10 - z5-3 Always 3 Ω or less
D51-11 - z5-4 Always 3 Ω or less
D51-12 - z5-5 Always 3 Ω or less
D52-1 - z7-2 Always Below 1 Ω
D52-2 - z7-1 Always Below 1 Ω
D52-3 - z6-1 Always Below 1 Ω
D52-4 - z6-2 Always Below 1 Ω

for Single Airbag System:
Tester Connection Condition Specified Condition
D51-1 - z4-3 Always 3 Ω or less
D51-2 - z4-4 Always 3 Ω or less
D51-2 - z5-6 Always 3 Ω or less
D51-8 - z4-2 Always 3 Ω or less
D51-8 - z5-1 Always 3 Ω or less
D51-10 - z5-3 Always 3 Ω or less
D51-11 - z5-4 Always 3 Ω or less
D51-12 - z5-5 Always 3 Ω or less
D52-1 - z6-2 Always Below 1 Ω
D52-2 - z6-1 Always Below 1 Ω



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

Standard Resistance:
for Dual Airbag System:
Tester Connection Condition Specified Condition
D51-1 - z4-3 Always 3 Ω or less
D51-2 - z4-4 Always 3 Ω or less
D51-2 - z5-6 Always 3 Ω or less
D51-8 - z4-2 Always 3 Ω or less
D51-8 - z5-1 Always 3 Ω or less
D51-10 - z5-3 Always 3 Ω or less
D51-11 - z5-4 Always 3 Ω or less
D51-12 - z5-5 Always 3 Ω or less
D52-1 - z7-2 Always Below 1 Ω
D52-2 - z7-1 Always Below 1 Ω
D52-3 - z6-1 Always Below 1 Ω
D52-4 - z6-2 Always Below 1 Ω

for Single Airbag System:
Tester Connection Condition Specified Condition
D51-1 - z4-3 Always 3 Ω or less
D51-2 - z4-4 Always 3 Ω or less
D51-2 - z5-6 Always 3 Ω or less
D51-8 - z4-2 Always 3 Ω or less
D51-8 - z5-1 Always 3 Ω or less
D51-10 - z5-3 Always 3 Ω or less
D51-11 - z5-4 Always 3 Ω or less
D51-12 - z5-5 Always 3 Ω or less
D52-1 - z6-2 Always Below 1 Ω
D52-2 - z6-1 Always Below 1 Ω



iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
for Dual Airbag System:
Tester Connection Condition Specified Condition
D51-1 - z4-3 Always 3 Ω or less
D51-2 - z4-4 Always 3 Ω or less
D51-2 - z5-6 Always 3 Ω or less
D51-8 - z4-2 Always 3 Ω or less
D51-8 - z5-1 Always 3 Ω or less
D51-10 - z5-3 Always 3 Ω or less
D51-11 - z5-4 Always 3 Ω or less
D51-12 - z5-5 Always 3 Ω or less
D52-1 - z7-2 Always Below 1 Ω
D52-2 - z7-1 Always Below 1 Ω
D52-3 - z6-1 Always Below 1 Ω
D52-4 - z6-2 Always Below 1 Ω

for Single Airbag System:
Tester Connection Condition Specified Condition
D51-1 - z4-3 Always 3 Ω or less
D51-2 - z4-4 Always 3 Ω or less
D51-2 - z5-6 Always 3 Ω or less
D51-8 - z4-2 Always 3 Ω or less
D51-8 - z5-1 Always 3 Ω or less
D51-10 - z5-3 Always 3 Ω or less
D51-11 - z5-4 Always 3 Ω or less
D51-12 - z5-5 Always 3 Ω or less
D52-1 - z6-2 Always Below 1 Ω
D52-2 - z6-1 Always Below 1 Ω


If the result is not as specified, replace the spiral cable with sensor sub-assembly.