Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297734 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1434/23  Open in Evaporator Sensor Circuit  B1435/-23  Short in Evaporator Sensor Circuit  


DESCRIPTION

The evaporator temperature sensor (No. 1 cooler thermistor) is installed on the No. 1 cooler evaporator sub-assembly in the air conditioner unit to detect the temperature of the air that has passed through the No. 1 cooler evaporator sub-assembly and is used to control the air conditioning. It sends signals to the air conditioning control assembly. The resistance of the evaporator temperature sensor (No. 1 cooler thermistor) changes in accordance with the cooled air temperature that has passed through the No. 1 cooler evaporator sub-assembly. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning control assembly applies voltage (5 V) to the evaporator temperature sensor (No. 1 cooler thermistor) and reads voltage changes as the resistance of the evaporator temperature sensor (No. 1 cooler thermistor) changes. This sensor is used for frost prevention.

DTC No. DTC Detection Condition Trouble Area
B1434/23 Open in evaporator sensor circuit
·

Evaporator temperature sensor (No. 1 cooler thermistor)

·

Harness or connector between evaporator temperature sensor (No. 1 cooler thermistor) and air conditioning control assembly

·

Air conditioning control assembly


B1435/-23 Short in evaporator sensor circuit
·

Evaporator temperature sensor (No. 1 cooler thermistor)

·

Harness or connector between evaporator temperature sensor (No. 1 cooler thermistor) and air conditioning control assembly

·

Air conditioning control assembly



WIRING DIAGRAM

E248912E03
4.635,1.385 4.885,1.552 0.25,0.167 10 false SG 4.427,1.271 4.542,1.417 0.115,0.146 10 false 6 2.406,0.833 2.531,0.99 0.125,0.156 10 false 1 2.406,1.271 2.531,1.427 0.125,0.156 10 false 2 3.927,2.198 6.677,2.385 2.75,0.188 10 false AIR CONDITIONING CONTROL ASSEMBLY 0.469,1.948 3.135,2.302 2.667,0.354 10 false EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THEMISTOR) 4.635,0.948 4.844,1.115 0.208,0.167 10 false TE 4.375,0.833 4.563,0.99 0.188,0.156 10 false 17 0.479,1.781 0.76,1.948 0.281,0.167 10 false A25 3.938,2.042 4.219,2.208 0.281,0.167 10 false D20

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Evaporator Temp Sensor
(Evap Temp)
Evaporator temperature sensor (No. 1 cooler thermistor) /
Min.: -82.48°C (-116.46°F)
Max.: 153.55°C (308.39°F)
Actual evaporator temperature displayed -

OK:

The display is as specified in the normal condition column.


Result:
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C




A

2.CHECK FOR DTC

B

C

3.INSPECT EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR)
3.INSPECT EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR)
a.

Remove the evaporator temperature sensor (No. 1 cooler thermistor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>REMOVAL).


b.

Inspect the evaporator temperature sensor (No. 1 cooler thermistor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>INSPECTION)



OK

4.CHECK HARNESS AND CONNECTOR (EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR) - AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPLACE EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR)

4.CHECK HARNESS AND CONNECTOR (EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR) - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the D20 air conditioning control assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-1 - D20-17(TE) Always Below 1 Ω
A25-2 - D20-6(SG) Always Below 1 Ω
A25-1 - Body ground Always 10 kΩ or higher
A25-2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR