Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297743 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  INSTALLATION  


PROCEDURE

Hide 1.INSPECT MAGNET CLUTCH CLEARANCE

a.
E373537

Clamp the cooler compressor in a vise between aluminum plates.


b.

Set the dial indicator to the magnet clutch hub as shown in the illustration.


c.

Connect the battery positive (+) lead to terminal 1 of the magnet clutch connector and the negative (-) lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard:

0.25 to 0.50 mm (0.010 to 0.020 in.)


If the measured value is not within the standard clearance, replace the compressor with magnet clutch.


d.

Remove the cooler compressor from the vise.


Hide 2.ADJUST COMPRESSOR OIL LEVEL

a.

for HFC-134a (R134a):

i.
E248883

When replacing the compressor with motor assembly with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

Drain oil from the new compressor assembly, and then add new oil so that the amount of oil in the new compressor assembly is the same as that in the compressor assembly to be replaced.


HINT:

The drain bolt and washer can be reused.


NOTICE:
·

When checking the compressor oil level, observe the precautions on the cooler removal/installation.

·

If a new compressor is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be excessive. This prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.

·

If the volume of oil remaining in the removed compressor is too small, check for oil leaks.

·

Be sure to use ND-OIL 8 or equivalent for compressor oil.





b.

for HFO-1234yf (R1234yf):

i.
E248883

When replacing the compressor with motor assembly with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

Drain oil from the new compressor assembly, and then add new oil so that the amount of oil in the new compressor assembly is the same as that in the compressor assembly to be replaced.


HINT:

The drain bolt and washer can be reused.


NOTICE:
·

When checking the compressor oil level, observe the precautions on the cooler removal/installation.

·

If a new compressor is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be excessive. This prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.

·

If the volume of oil remaining in the removed compressor is too small, check for oil leaks.

·

Be sure to use ND-OIL 12 or equivalent for compressor oil.





Hide 88310E 3.INSTALL COMPRESSOR WITH MAGNET CLUTCH

a.
E250732E02
1.219,1.948 1.479,2.115 0.26,0.167 10 true <1> 2.25,1.969 2.542,2.135 0.292,0.167 10 true <2> 1.625,0.156 1.906,0.323 0.281,0.167 10 false <3>

Install the compressor with magnet clutch with the 3 bolts.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


b.

Connect the connector.


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the attached vinyl tape from the hose.


b.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor with magnet clutch.

Compressor oil:
for HFC-134a (R134a):

ND-OIL 8 or equivalent

for HFO-1234yf (R1234yf):

ND-OIL 12 or equivalent



c.

Install the O-ring onto the No. 1 cooler refrigerant discharge hose.


d.

Install the No. 1 cooler refrigerant discharge hose onto the compressor with magnet clutch with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 88704 5.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the hose.


b.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor with magnet clutch.

Compressor oil:
for HFC-134a (R134a):

ND-OIL 8 or equivalent

for HFO-1234yf (R1234yf):

ND-OIL 12 or equivalent



c.

Install the O-ring onto the suction hose sub-assembly.


d.

Install the suction hose sub-assembly onto the compressor with magnet clutch with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)