Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297762 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RHD and LHD vehicle.


PROCEDURE

Hide 85192 1.REMOVE WINDSHIELD WIPER ARM COVER

Hide 2.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH

Hide 3.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH

Hide 53866J 4.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

Hide 53867H 5.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

HINT:

The procedure described below is for the RH side.


Hide 55781 6.REMOVE COWL VENTILATOR LOUVER

Hide 63310 7.REMOVE ROOF HEADLINING ASSEMBLY

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step. Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 56111 8.REMOVE WINDSHIELD GLASS

a.
B309158E02
2.531,0.552 1.99,0.823 true 1.833,0.823 2,0.979 0.167,0.156 10 false *1

Apply protective tape to the installation position of the windshield glass on the vehicle body.

Text in Illustration
*1 Protective Tape

HINT:

Apply protective tape to the area around installation surface to prevent it from being scratched.



b.
B187142E07
2.396,0.385 2.198,0.615 false 2.938,0.667 2.938,0.802 false 0.938,1 0.792,1.313 false 1.573,1.188 1.406,1.313 false 2.427,0.26 2.708,0.438 0.281,0.177 10 false *a 2.865,0.823 3.208,1.01 0.344,0.188 10 false *1 1.219,1.26 1.448,1.448 0.229,0.188 10 false *2 0.625,1.302 0.854,1.479 0.229,0.177 10 false *3

Using a knife, cut off the windshield moulding outside, as shown in the illustration.

Text in Illustration
*1 Body
*2 Windshield moulding outside
*3 Windshield glass
*a Cut

CAUTION:
·

Do not damage the vehicle body with the knife.

·

If the vehicle body is damaged, repair the damaged portion by applying an anti-rust coating after removing the windshield glass.




c.
B309159E02
1.635,0.313 1.51,0.313 1.51,0.313 1.51,0.75 true 1.646,0.583 1.51,0.583 true 1.427,0.771 1.583,0.969 0.156,0.198 10 false *a

Place matchmarks on the windshield glass and vehicle body on the locations indicated in the illustration.

Text in Illustration
*a Matchmark

HINT:

Matchmarks are not necessary if the windshield glass is not going to be reused.



d.
B313102E02
0.49,1.375 0.365,1.708 false 1.26,0.51 1.042,0.427 false 1.646,3.708 1.646,4.167 false 0.781,2.708 1.688,3.375 1.688,3.375 2.604,2.719 true 1.563,4.24 1.719,4.385 0.156,0.146 10 false *4 0.26,1.76 0.417,1.906 0.156,0.146 10 false *1 0.875,0.323 1.031,0.469 0.156,0.146 10 false *2 1.635,3.417 1.792,3.563 0.156,0.146 10 false *3

Pass a piano wire between the vehicle body and windshield glass from the interior, as shown in the illustration.

Text in Illustration
*1 Wooden Block
*2 Plastic Sheet
*3 Windshield Glass Stopper
*4 Piano Wire


e.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


f.

Cut off the adhesive by pulling the piano wire around the windshield glass.

NOTICE:
·

When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.

·

Do not damage the windshield glass.




g.
B309162E01
2.16,3.426 2.311,3.581 0.151,0.155 10 *1 1.823,3.537 2.143,3.537 false

Using suction cups, disengage the windshield glass stopper and remove the windshield glass.

Text in Illustration
*1 Windshield Glass Stopper

NOTICE:
·

There are windshield glass stopper on the windshield glass, as shown in the illustration. Be careful not to damage the windshield glass stopper when cutting off the adhesive.

·

To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.




Hide 56117A 9.REMOVE WINDOW GLASS ADHESIVE DAM

a.
B309163E03
0.219,1.698 0.219,0.979 0.219,0.979 0.531,0.979 true 3,0.24 2.313,0.24 2.313,0.24 2.313,0.479 true 2.875,0.25 2.875,0.573 2.875,0.573 2.771,0.573 true 0.219,1.542 0.771,1.542 true 3.052,0.167 3.24,0.313 0.188,0.146 10 false *1 0.146,1.75 0.333,1.896 0.188,0.146 10 false *1 0.188,0.104 0.375,0.25 0.188,0.146 10 false *a

Using a scraper, remove the window glass adhesive dam.

Text in Illustration
*1 Window Glass Adhesive Dam
*a Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new one.




Hide 56119 10.REMOVE LOWER WINDSHIELD GLASS SEAL

a.
B309163E02
0.514,1.374 0.855,1.222 false 0.843,1.051 1.015,1.201 0.172,0.150 10 *1 2.918,1.377 2.576,1.225 false 2.36,1.055 2.532,1.205 0.172,0.150 10 *1 0.161,0.174 0.334,0.324 0.172,0.150 10 *a

Using a scraper, remove the 2 windshield glass seals.

Text in Illustration
*1 Windshield Glass Seal
*a Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the lower windshield glass seal with a new one.




Hide 75533G 11.REMOVE WINDSHIELD OUTSIDE MOULDING

a.
B309164E01
1.606,0.125 1.771,0.277 0.166,0.151 10 *1 0.093,0.104 0.259,0.255 0.166,0.151 10 *a 1.709,0.498 1.709,0.288 false

Using a scraper, remove the windshield outside moulding with the upper windshield glass seal.

Text in Illustration
*1 Windshield Outside Moulding
*a Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.




Hide 56114 12.REMOVE UPPER WINDSHIELD GLASS SEAL

NOTICE:

Be sure to replace the upper windshield glass seal with a new one.


Hide 56115A 13.REMOVE NO. 1 WINDSHIELD GLASS STOPPER

a.
B309165E02
0.771,0.448 1.031,0.885 true 2.646,0.448 2.375,0.885 true 2.26,0.917 2.427,1.063 0.167,0.146 10 false *1 1.031,0.927 1.198,1.073 0.167,0.146 10 false *2 0.208,0.01 0.375,0.156 0.167,0.146 10 false *a

Using a scraper, remove the No. 1 windshield glass stopper.

Text in Illustration
*1 No. 1 Windshield Stopper
*2 No. 2 Windshield Stopper
*a Back Side

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 1 windshield glass stopper with a new one.




Hide 56116C 14.REMOVE NO. 2 WINDSHIELD GLASS STOPPER

HINT:

Use the same procedure as for the No. 1 windshield glass stopper.


Hide 56111 15.CLEAN WINDSHIELD GLASS

a.
B149736

Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



b.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.




Hide 16.CLEAN VEHICLE BODY

a.

Clean and shape the contact surfaces of the vehicle body.

i.

Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.


B309172E02
1.833,0.656 2.344,0.51 false 2.396,0.427 2.583,0.604 0.188,0.177 10 false *1 4.427,1.563 4.615,1.74 0.188,0.177 10 false a

Standard Dimension:
Area Dimension
a 2.0 mm (0.0787 in.)


Text in Illustration
*1 Body - -
V100145

Adhesive - -


ii.

Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.