The power window regulator motor assembly is operated by the power window master switch assembly or power window regulator switch assembly. The power window regulator motor assembly has motor, regulator and ECU functions. These DTCs are output when the ECU built into the regulator motor and master switch determines that the power window master switch assembly or power window regulator switch assembly is stuck.
When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
When the jam protection function malfunctions and prevents the door glass from closing completely, the following procedure can be used to cancel the jam protection function and allow the door glass to be closed*1.
Repeat the AUTO UP maintain → jam protection function operation twice in succession*2.
The third repeat of the AUTO UP maintain operation will cause the position of the upper edge of the door glass to be relearned, allowing the door glass to be closed.
*1: In some cases, the state of the door glass or regulator may prevent the glass from being closed, even in this mode.
*2: If any action other that the AUTO UP operation (DOWN operation, IG OFF, timer-operated OFF, index operation, etc.) is performed between the operation of the jam protection function and the AUTO UP maintain, this count will be reset.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2312 | ·
The power window regulator master switch is stuck ·
Power window regulator master switch assembly held in same position for more than 20 seconds |
Power window regulator master switch assembly |
| B2315 | ·
The power window regulator switch is stuck ·
Power window regulator switch assembly held in same position for more than 20 seconds |
·
Power window regulator master switch assembly ·
Power window regulator switch assembly ·
Wire harness and connector |
Clear the DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).
Check the DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2312 is output | A |
| DTC B2315 is output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Master Switch / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P Door P/W Auto SW | Front passenger side power window auto switch signal / ON or OFF | ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window switch not operated |
- |
| P Door P/W Up SW | Front passenger side power window manual up signal / ON or OFF | ON: Front passenger side power window manual up switch operated
OFF: Front passenger side power window switch not operated |
- |
| P Door P/W Down SW | Front passenger side power window manual down signal / ON or OFF | ON: Front passenger side power window manual down switch operated
OFF: Front passenger side power window switch not operated |
- |
The GTS display changes normally when regulator switch is operated.
OK
NG
Disconnect the E8*1 or F6*2 power window regulator master switch assembly connector.
Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E8-2 (UART) - F6-2 (UART) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E8-2 (UART)*1 - Body ground | Always | 10 kΩ or higher |
| F6-2 (UART)*2 - Body ground | Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
OK
NG