Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297766 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2313  Driver Side Glass Position Initialization Incomplete  B2316  Passenger Side Glass Position Initialization Incomplete  


DESCRIPTION

The power window regulator motor assembly (driver side or front passenger side) is operated by the power window regulator master switch assembly or the power window regulator switch assembly. When the ECU (power window regulator master switch assembly) determines that the power window regulator master switch assembly or the power window regulator switch assembly has not been initialized, or the pulse output circuit of the power window regulator motor assembly (driver side or front passenger side) is abnormal, DTC B2313 or B2316 is stored.

DTC No. DTC Detection Condition Trouble Area
B2313
·

Power window regulator master switch assembly not initialized

·

Power window regulator motor assembly (for driver side) malfunction (pulse sensor)

·

Open or short between power window regulator motor assembly (for driver side) and power window regulator master switch assembly


·

Power window regulator master switch assembly (for driver side) not initialized

·

Power window regulator master switch assembly (for driver side)

·

Power window regulator motor assembly (for driver side)

·

Wire harness or connector


B2316
·

Power window regulator switch assembly not initialized

·

Power window regulator motor assembly (for front passenger side) malfunction (pulse sensor)

·

Open or short between power window regulator motor assembly (for front passenger side) and power window regulator switch assembly


·

Power window regulator switch assembly (for front passenger side) not initialized

·

Power window regulator switch assembly (for front passenger side)

·

Power window regulator motor assembly (for front passenger side)

·

Wire harness or connector



WIRING DIAGRAM

B399298E09
2.208,0.917 2.594,1.25 0.385,0.333 10 false SN1 1.979,1.344 2.365,1.677 0.385,0.333 10 false 1 1.979,0.802 2.365,1.135 0.385,0.333 10 false 8 1.365,0.823 1.75,1.156 0.385,0.333 10 false 6 1.375,1.333 1.76,1.667 0.385,0.333 10 false 2 0.958,1.438 1.344,1.771 0.385,0.333 10 false SN2 0.958,0.948 1.344,1.281 0.385,0.333 10 false SN1 2.208,1.417 2.573,1.75 0.365,0.333 10 false SN2 0.156,1.958 1.802,2.667 1.646,0.708 10 false Power Window Regulator Motor Assembly RH 0.167,1.771 0.531,2.104 0.365,0.333 10 false F1 4.646,1.479 5.01,1.813 0.365,0.333 10 false SN2 5.75,1.448 6.115,1.781 0.365,0.333 10 false SN2 4.646,0.969 5.01,1.302 0.365,0.333 10 false SN1 5.75,0.927 6.115,1.26 0.365,0.333 10 false SN1 4.208,1.792 4.583,2.125 0.375,0.333 10 false GND 2.635,1.792 3.01,2.125 0.375,0.333 10 false GND 4.198,1.177 4.656,1.51 0.458,0.333 10 false UART 2.563,1.198 3.021,1.531 0.458,0.333 10 false UART 3.979,1.063 4.365,1.396 0.385,0.333 10 false 2 3.979,1.667 4.365,2 0.385,0.333 10 false 5 3.073,1.667 3.458,2 0.385,0.333 10 false 5 3.073,1.063 3.458,1.396 0.385,0.333 10 false 2 1.792,2.656 2.135,2.906 0.344,0.25 10 false F6 1.781,2.875 3.427,3.583 1.646,0.708 10 false Power Window Regulator Switch Assembly 3.865,2.865 5.521,3.573 1.656,0.708 10 false Power Window Regulator Master Switch Assembly 3.865,2.646 4.146,2.865 0.281,0.219 10 false E8 5.417,1.792 5.698,2 0.281,0.208 10 false E5 5.073,0.865 5.458,1.198 0.385,0.333 10 false 8 5.073,1.354 5.458,1.688 0.385,0.333 10 false 1 5.531,1.344 5.917,1.677 0.385,0.333 10 false 2 5.531,0.854 5.917,1.188 0.385,0.333 10 false 6 5.417,1.979 7.063,2.688 1.646,0.708 10 false Power Window Regulator Motor Assembly LH 0.24,0.167 1.063,0.417 0.823,0.25 12 false for LHD:

B399298E08
2.208,0.938 2.594,1.271 0.385,0.333 10 false SN1 1.99,1.333 2.375,1.667 0.385,0.333 10 false 1 1.99,0.823 2.375,1.156 0.385,0.333 10 false 8 1.354,0.833 1.74,1.167 0.385,0.333 10 false 6 1.354,1.333 1.74,1.667 0.385,0.333 10 false 2 0.958,1.438 1.344,1.771 0.385,0.333 10 false SN2 0.958,0.938 1.344,1.271 0.385,0.333 10 false SN1 0.281,0.125 1.188,0.458 0.906,0.333 12 false for RHD: 2.208,1.438 2.573,1.771 0.365,0.333 10 false SN2 0.146,1.948 1.792,2.656 1.646,0.708 10 false Power Window Regulator Motor Assembly LH 0.167,1.771 0.531,2.104 0.365,0.333 10 false E5 4.677,1.469 5.042,1.802 0.365,0.333 10 false SN2 5.74,1.469 6.104,1.802 0.365,0.333 10 false SN2 4.677,0.958 5.042,1.292 0.365,0.333 10 false SN1 5.74,0.969 6.104,1.302 0.365,0.333 10 false SN1 4.208,1.792 4.583,2.125 0.375,0.333 10 false GND 2.646,1.802 3.021,2.135 0.375,0.333 10 false GND 4.198,1.188 4.656,1.521 0.458,0.333 10 false UART 2.583,1.177 3.042,1.51 0.458,0.333 10 false UART 3.99,1.073 4.375,1.406 0.385,0.333 10 false 2 3.99,1.677 4.375,2.01 0.385,0.333 10 false 5 3.052,1.667 3.438,2 0.385,0.333 10 false 5 3.052,1.052 3.438,1.385 0.385,0.333 10 false 2 1.792,2.635 2.156,2.969 0.365,0.333 10 false E8 1.792,2.823 3.438,3.531 1.646,0.708 10 false Power Window Regulator Switch Assembly 3.875,2.844 5.531,3.552 1.656,0.708 10 false Power Window Regulator Master Switch Assembly 3.865,2.667 4.229,3 0.365,0.333 10 false F6 5.427,1.802 5.792,2.135 0.365,0.333 10 false F1 5.052,0.844 5.438,1.177 0.385,0.333 10 false 8 5.042,1.365 5.427,1.698 0.385,0.333 10 false 1 5.542,1.365 5.927,1.698 0.385,0.333 10 false 2 5.552,0.854 5.938,1.188 0.385,0.333 10 false 6 5.417,1.979 7.063,2.688 1.646,0.708 10 false Power Window Regulator Motor Assembly RH

PROCEDURE

1.PERFORM INITIALIZATION
a.

Turn the ignition switch to ON.


b.

Initialize the power window regulator master switch assembly or power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT

b.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Check for DTCs for the power window regulator motor assembly that has DTC B2313 or B2316 stored in its ECU.


OK:

DTC is not output.



Result
Result Proceed to
No DTCs output A
DTCs B2311 or B2314 is output B
DTCs B2312 or B2315 is output B
DTC B2313 is output C
DTC B2316 is output D


A

END (POWER WINDOW CONTROL SYSTEM HAS NOT BEEN INITIALIZED)

B

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

C

3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

D

5.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY
3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Using an oscilloscope, check the waveform.

U190296E02
2.417,1.302 2.823,1.031 true 2.417,1.573 2.698,1.854 true 1.427,1.281 1,0.844 true 0.24,1.115 0.635,1.396 0.396,0.281 10 false E8 0.25,1.563 0.646,1.844 0.396,0.281 10 false F6 0.583,1.573 0.979,1.854 0.396,0.281 10 false *B 0.573,1.115 0.969,1.396 0.396,0.281 10 false *A 0.354,0.177 0.75,0.458 0.396,0.281 10 false *a 2.823,0.833 3.219,1.115 0.396,0.281 10 false SN2 0.688,0.688 1.083,0.969 0.396,0.281 10 false GND 2.74,1.854 3.135,2.135 0.396,0.281 10 false SN1 6.479,1.156 6.875,1.438 0.396,0.281 10 false GND 6.469,1.781 6.865,2.063 0.396,0.281 10 false GND 4.188,1.156 4.583,1.438 0.396,0.281 10 false CH1 4.188,1.771 4.583,2.052 0.396,0.281 10 false CH2 4.073,0.188 4.469,0.469 0.396,0.281 10 false *b

Text in Illustration
*A for LHD *B for RHD
*a Component with harness connected (Power Window Regulator Master Switch Assembly) *b Waveform

OK:
Tester Connection Condition Tool Setting Specified Condition
CH1: E8-8 (SN1) - E8-5 (GND)*1
CH2: E8-1 (SN2) - E8-5 (GND)*1
CH1: F6-8 (SN1) - F6-5 (GND)*2
CH2: F6-1 (SN2) - F6-5 (GND)*2
Ignition switch ON, power window regulator master switch assembly OFF → UP or DOWN 5 V/DIV., 2 ms./DIV. Pulse generation (See waveform)



*1: for LHD

*2: for RHD


Result
Result Proceed to
NG A
OK B


A

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER SIDE))

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER SIDE))
a.

Disconnect the E8*1 or F6*2 power window regulator master switch assembly connector.


b.

Disconnect the E5*1 or F1*2 power window regulator motor assembly (for driver side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E8-8 (SN1) - E5-6 (SN1)*1 Always Below 1 Ω
E8-1 (SN2) - E5-2 (SN2)*1 Always Below 1 Ω
F6-8 (SN1) - F1-6 (SN1)*2 Always Below 1 Ω
F6-1 (SN2) - F1-2 (SN2)*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E8-8 (SN1) or E5-6 (SN1) - Body ground*1 Always 10 kΩ or higher
E8-1 (SN2) or E5-2 (SN2) - Body ground*1 Always 10 kΩ or higher
F6-8 (SN1) or F1-6 (SN1) - Body ground*2 Always 10 kΩ or higher
F6-1 (SN2) or F1-2 (SN2) - Body ground*2 Always 10 kΩ or higher



*1: for LHD

*2: for RHD



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.

Using an oscilloscope, check the waveform.

U190297E02
2.417,1.292 2.823,1.021 true 2.417,1.552 2.698,1.833 true 1.438,1.281 1.01,0.844 true 0.26,1.552 0.656,1.833 0.396,0.281 10 false E8 0.25,1.115 0.646,1.396 0.396,0.281 10 false F6 0.573,1.552 0.969,1.833 0.396,0.281 10 false *B 0.563,1.104 0.958,1.385 0.396,0.281 10 false *A 0.354,0.052 0.75,0.333 0.396,0.281 10 false *a 2.896,0.917 3.292,1.198 0.396,0.281 10 false SN2 0.719,0.635 1.115,0.917 0.396,0.281 10 false GND 2.75,1.792 3.146,2.073 0.396,0.281 10 false SN1 6.469,1.156 6.865,1.438 0.396,0.281 10 false GND 6.458,1.771 6.854,2.052 0.396,0.281 10 false GND 4.188,1.146 4.583,1.427 0.396,0.281 10 false CH1 4.188,1.771 4.583,2.052 0.396,0.281 10 false CH2 4.073,0.104 4.469,0.385 0.396,0.281 10 false *b

Text in Illustration
*A for LHD *B for RHD
*a Component with harness connected (Power Window Regulator Switch Assembly) *b Waveform

OK:
Tester Connection Condition Tool Setting Specified Condition
CH1: F6-8 (SN1) - F6-5 (GND)*1
CH2: F6-1 (SN2) - F6-5 (GND)*1
CH1: E8-8 (SN1) - E8-5 (GND)*2
CH2: E8-1 (SN2) - E8-5 (GND)*2
Ignition switch ON, power window regulator switch assembly OFF → UP or DOWN 5 V/DIV., 2 ms./DIV. Pulse generation (See waveform)



*1: for LHD

*2: for RHD


Result
Result Proceed to
NG A
OK B


A

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR (FOR FRONT PASSENGER SIDE))

B

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR (FOR FRONT PASSENGER SIDE))
a.

Disconnect the F6*1 or E8*2 power window regulator switch assembly connector.


b.

Disconnect the F1*1 or E5*2 power window regulator motor assembly (for passenger side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F6-8 (SN1) - F1-6 (SN1)*1 Always Below 1 Ω
F6-1 (SN2) - F1-2 (SN2)*1 Always Below 1 Ω
E8-8 (SN1) - E5-6 (SN1)*2 Always Below 1 Ω
E8-1 (SN2) - E5-2 (SN2)*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F6-8 (SN1) or F1-6 (SN1) - Body ground*1 Always 10 kΩ or higher
F6-1 (SN2) or F1-2 (SN2) - Body ground*1 Always 10 kΩ or higher
E8-8 (SN1) or E5-6 (SN1) - Body ground*2 Always 10 kΩ or higher
E8-1 (SN2) or E5-2 (SN2) - Body ground*2 Always 10 kΩ or higher



*1: for LHD

*2: for RHD



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR