The main body ECU (network gateway ECU) detects signals from the front door courtesy light switch. When the ON signal from the front door courtesy light switch is sent to the power window regulator master switch assembly via the main body ECU (network gateway ECU) using LIN communication system, the main body ECU (network gateway ECU) will lower the driver side door window about 20 mm (0.787 in.) automatically. When the OFF signal from the front door courtesy light switch is detected, the main body ECU (network gateway ECU) will raise the driver side door window to the fully-closed position automatically.
When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
When the jam protection function malfunctions and prevents the door glass from closing completely, the following procedure can be used to cancel the jam protection function and allow the door glass to be closed*1.
Repeat the AUTO UP maintain → jam protection function operation twice in succession*2.
The third repeat of the AUTO UP maintain operation will cause the position of the upper edge of the door glass to be relearned, allowing the door glass to be closed.
*1: In some cases, the state of the door glass or regulator may prevent the glass from being closed, even in this mode.
*2: If any action other that the AUTO UP operation (DOWN operation, IG OFF, timer-operated OFF, index operation, etc.) is performed between the operation of the jam protection function and the AUTO UP maintain, this count will be reset.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| D Door Courtesy SW | Driver side door courtesy light switch signal / ON or OFF | ON: Driver side door opened
OFF: Driver side door closed |
- |
On the GTS screen, ON or OFF is displayed accordingly.
OK
NG
Initialize the power window regulator master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Check the power window regulator master switch assembly is operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Driver side door power window operates normally.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Current D Door Glass Position Information | Glass position of the driver side power window / -100 to 700 | - | - |
Pulse generation.
OK
NG
Check the power window regulator master switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Driver side door power window operates normally.
| Result | Proceed to |
|---|---|
| Operate (Does not window glass operate) | A |
| Does not operate | B |
A
B
Temporarily replace the power window regulator motor assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>REMOVAL).
Check the power window regulator master switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Driver side door power window operates normally.
| Result | Proceed to |
|---|---|
| Operate | A |
| Does not operate | B |
A
B
Temporarily replace the power window regulator master switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).
Check the power window regulator master switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Driver side door power window operates normally.
| Result | Proceed to |
|---|---|
| Does not operate | A |
| Operate | B |
A
B
Temporarily replace the power window regulator motor assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>REMOVAL).
Check the power window regulator master switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Driver side door power window operates normally.
| Result | Proceed to |
|---|---|
| Operate | A |
| Does not operate | B |
A
B