Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297816 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU (network gateway ECU). The main body ECU (network gateway ECU) turns on or off the headlights and taillights according to the signal.

DTC No. DTC Detection Condition Trouble Area
B1244
·

Malfunction in automatic light control sensor.

·

Open or short in automatic light control sensor circuit.


·

Automatic light control sensor

·

Main body ECU (Network gateway ECU)

·

Harness or connector



WIRING DIAGRAM

E199045E12
0.635,1.969 2.25,2.344 1.615,0.375 10 false Main Body ECU (Network Gateway ECU) 4.927,1.708 6.438,2.146 1.51,0.438 10 false Automatic Light Control Sensor 2.573,0.615 2.813,0.802 0.24,0.188 10 false 15 2.573,0.854 2.813,1.042 0.24,0.188 10 false 14 2.563,1.083 2.802,1.271 0.24,0.188 10 false 13 4.813,0.583 4.917,0.771 0.104,0.188 10 false 3 4.813,0.833 4.938,1 0.125,0.167 10 false 4 4.813,1.094 4.927,1.281 0.115,0.188 10 false 5 2.125,0.698 2.5,0.896 0.375,0.198 10 false CLTB 2.115,0.927 2.49,1.125 0.375,0.198 10 false CLTS 2.115,1.167 2.49,1.365 0.375,0.198 10 false CLTE 5,0.688 5.375,0.885 0.375,0.198 10 false CLTB 4.99,0.948 5.365,1.146 0.375,0.198 10 false CLTS 4.99,1.188 5.365,1.385 0.375,0.198 10 false CLTE 0.646,1.792 1.021,1.99 0.375,0.198 10 false D6 4.927,1.552 5.208,1.729 0.281,0.177 10 false D45

PROCEDURE

1.READ VALUE USING GTS (ILLUMINATION RATE INFO)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate information / 0 ms to 99.99 ms Value is output according to ambient light levels -

OK:

Normal condition listed above is displayed.


Result:
Result Proceed to
NG A
OK B




A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)

B

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the D6 main body ECU (network gateway ECU) connector.


b.

Disconnect the D45 automatic light control sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D6-13 (CLTE) - D45-6 (CLTE) Always Below 1 Ω
D6-14 (CLTS) - D45-4 (CLTS) Always Below 1 Ω
D6-15 (CLTB) - D45-3 (CLTB) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D6-13 (CLTE) - Body ground Always 10 kΩ or higher
D6-14 (CLTS) - Body ground Always 10 kΩ or higher
D6-15 (CLTB) - Body ground Always 10 kΩ or higher




OK

3.CHECK MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU (NETWORK GATEWAY ECU)
a.

Reconnect the D6 main body ECU (network gateway ECU) connector.


b.
U147264E02
2.052,1.302 2.292,1.615 true 1.917,1.333 1.229,1.656 true 1.677,0.417 1.969,0.573 0.292,0.156 10 false D6 2.24,1.635 2.708,1.854 0.469,0.219 10 false CLTE 0.823,1.625 1.198,1.823 0.375,0.198 10 false CLTS 0.177,0.031 0.469,0.188 0.292,0.156 10 false *a

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D6-13 (CLTE) - D6-14 (CLTS) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
D6-13 (CLTE) - Body ground Always 10 kΩ or higher



Text in Illustration
*a Component with harness connected
(Main Body ECU (Network Gateway ECU))


OK

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.

Reconnect the automatic light control sensor (See page Vehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>REMOVAL).


b.

Inspect the automatic light control sensor (See page Vehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>INSPECTION).



OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR