Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297816 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Low Beam Headlight Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) receives headlight dimmer switch assembly information signals, and illuminates the low beam headlight.

WIRING DIAGRAM

E252209E06
0.99,3.74 2.552,4.073 1.563,0.333 10 false to Low Beam Headlight 3.563,3.042 5.219,3.677 1.656,0.635 10 false Instrument Panel Junction Block Assembly 5.438,3.688 7.156,4.354 1.719,0.667 10 false Main Body ECU (Network Gateway ECU) 2.885,1.865 3,2.021 0.115,0.156 10 false 1 2.885,2.385 3,2.542 0.115,0.156 10 false 3 2.156,1.875 2.271,2.031 0.115,0.156 10 false 2 2.156,2.385 2.271,2.542 0.115,0.156 10 false 5 2.427,2.823 2.771,2.969 0.344,0.146 10 false H-LP 4.906,1.771 5.083,1.927 0.177,0.156 10 false 29 4.896,2.5 5.073,2.656 0.177,0.156 10 false 30 4.885,1.969 5.094,2.115 0.208,0.146 10 false 3A 4.885,2.708 5.094,2.854 0.208,0.146 10 false 3C 3.594,1.771 3.781,1.927 0.188,0.156 10 false 17 3.594,1.969 3.813,2.115 0.219,0.146 10 false 3C 5.646,1.042 5.823,1.198 0.177,0.156 10 false 11 5.594,1.25 5.865,1.396 0.271,0.146 10 false A73 5.958,1.24 6.323,1.458 0.365,0.219 10 false DIM 5.958,2.698 6.427,2.958 0.469,0.26 10 false HRLY 0.146,2.469 0.948,2.792 0.802,0.323 10 false from Battery 5.677,1.76 5.792,1.917 0.115,0.156 10 false 1 5.635,1.969 5.844,2.115 0.208,0.146 10 false D5 5.688,2.49 5.802,2.646 0.115,0.156 10 false 2 5.594,2.698 5.865,2.844 0.271,0.146 10 false A73

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (H-LP RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Low beam headlight relay ON/OFF -

OK:

Headlight relay operates (low beam headlights illuminate).


Result:
Result Proceed to
NG A
OK B




A

2.INSPECT H-LP RELAY

B

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

2.INSPECT H-LP RELAY
a.

Remove the H-LP relay from the engine room relay block.


b.


OK

3.CHECK HARNESS AND CONNECTOR (H-LP RELAY - BATTERY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (H-LP RELAY - BATTERY)
E252212E01
0.16,0.118 0.346,0.279 0.186,0.161 10 *a

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*a Engine Room Relay Block
(H-LP Relay Terminal)



OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - MAIN BODY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the A73 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Relay terminal 2 - A73-11 (DIM) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A73-11 (DIM) - Body ground Always 10 kΩ or higher



OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Relay terminal 1 - 3C-17 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
3C-17 - Body ground Always 10 kΩ or higher



OK

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the 3A and 3C instrument panel junction block assembly connector.


b.

Disconnect the D5 and A73 main body ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
3A-29 - D5-1 Always Below 1 Ω
3C-30 - A73-2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D5-1 - Body ground Always 10 kΩ or higher
A73-2(HRLY) - Body ground Always 10 kΩ or higher



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


U147262E02
0.313,0.188 0.5,0.344 0.188,0.156 10 false *a 1.719,0.427 1.917,0.573 0.198,0.146 10 false 3C 4.719,0.427 4.927,0.583 0.208,0.156 10 false 3A

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3C-17 - 3A-29 Always Below 1 Ω
3C-17 - 3C-30 Always Below 1 Ω



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY