Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297816 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  High Beam Headlight Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) receives headlight dimmer switch information signals, and illuminates the high beam headlight.

WIRING DIAGRAM

E252211E04
3.563,1.469 3.677,1.625 0.115,0.156 10 false 1 2.813,1.49 2.927,1.646 0.115,0.156 10 false 2 2.813,2 2.927,2.156 0.115,0.156 10 false 5 3.563,1.99 3.677,2.146 0.115,0.156 10 false 3 3.104,2.448 3.375,2.594 0.271,0.146 10 false DIM 4.917,0.885 5.094,1.042 0.177,0.156 10 false 11 5.177,0.979 5.531,1.198 0.354,0.219 10 false DIM 4.771,2.573 5.083,2.729 0.313,0.156 10 false A73 4.906,1.469 5.115,1.625 0.208,0.156 10 false 23 4.75,2.75 6.427,3.125 1.677,0.375 10 false Main Body ECU (Network Gateway ECU) 0.49,2.094 1.26,2.292 0.771,0.198 10 false from Battery 1.563,3.167 3.094,3.354 1.531,0.188 10 false to High Beam Headlight

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (HEAD LIGHT HI)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test


e.

Check that the relay operates.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Head Light Hi Headlight dimmer relay ON/OFF -

OK:

Relay operates (high beam headlights illuminate).


Result:
Result Proceed to
NG A
OK B




A

2.INSPECT DIM RELAY

B

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

2.INSPECT DIM RELAY
a.

Remove the DIM relay from the engine room relay block.




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - DIM RELAY)

NG

REPLACE DIM RELAY

3.CHECK HARNESS AND CONNECTOR (BATTERY - DIM RELAY)
E252213E01
0.161,0.12 0.347,0.281 0.186,0.161 10 *a

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*a Engine Room Relay Block
(DIM Relay Terminal)



OK

4.CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the A73 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Relay terminal 2 - A73-11 (DIM) Always Below 1 Ω
Relay terminal 1 - A73-23 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A73-11 (DIM) - Body ground Always 10 kΩ or higher
A73-23 - Body ground Always 10 kΩ or higher



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR