the low beam headlights do not illuminate, or a communication malfunction is detected between the headlight assembly and headlight leveling ECU assembly.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Headlight Relay | Headlight relay | ON/OFF | - |
The daytime running lights illuminate.
OK
NG
Disconnect the A60 or A38 Headlight Assembly RH or LH connectors.
Disconnect the A16 headlight leveling ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-8 - A16-13 (R-DIAG) | Always | Below 1 Ω |
| A60-8 - A16-15 (L-DIAG) | Always | Below 1 Ω |
| A38-8 or A16-13 (R-DIAG) - Body ground | Always | 10 kΩ or higher |
| A60-8 or A16-15 (L-DIAG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A16-13 (R-DIAG) - Body ground | Always | Below 1.5 V |
| A16-15 (L-DIAG) - Body ground | Always | Below 1.5 V |
| *a | Component without harness connected
(Headlight Leveling ECU Assembly) |
OK
NG
Remove the H-LP relay from the engine room relay block.
Inspect the H-LP relay (See pageVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the H-LP relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay Terminal 5 - Body ground | Always | 11 to 14 V |
| *a | Engine Room Relay Block
(H-LP Relay Terminal) |
OK
NG
Remove the H-LP relay from the engine room relay block.
Disconnect the A73 main body ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay Terminal 2 - A73-11 | Always | Below 1 Ω |
| A73-11 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the H-LP relay from the engine room relay block.
Disconnect the 3C Instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay Terminal 1 - 3C-17 | Always | Below 1 Ω |
| 3C-17 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the 3A and 3C Instrument panel junction block assembly connector.
Disconnect the A73 and D5 main body ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-29 - D5-1 (HRLYD) | Always | Below 1 Ω |
| 3C-30 - A73-2 (HRLY) | Always | Below 1 Ω |
| 3A-29 or D5-1 (HRLYD) - Body ground | Always | 10 kΩ or higher |
| 3C-30 or A73-2 (HRLY) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly (See page ).
Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-17 - 3A-29 | Always | Below 1 Ω |
| 3C-17 - 3C-30 | Always | Below 1 Ω |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
OK
NG