Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  P0340  Camshaft Position Sensor Circuit Malfunction  


DESCRIPTION

The Camshaft Position (CMP) sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed onto the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft passes through the CMP sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the CMP sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit Malfunction No input of a certain number of camshaft position sensor signal for 2 seconds or more while engine running (1 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A266588E04
0.792,1.927 2.458,2.604 1.667,0.677 10 CAMSHAFT POSITION SENSOR 0.792,1.75 1.375,2.073 0.583,0.323 10 C9 1.99,0.833 2.438,1.219 0.448,0.385 10 1 1.99,1.323 2.479,1.865 0.49,0.542 10 2 2.927,1.719 3.74,2.188 0.813,0.469 10 (Shielded) 4.771,0.833 5.115,1.188 0.344,0.354 10 8 4.708,1.323 5.052,1.646 0.344,0.323 10 28 4.958,0.844 5.438,1.198 0.479,0.354 10 N2+ 4.958,1.323 5.521,1.875 0.563,0.552 10 N2- 5.417,2.229 6.385,2.792 0.969,0.563 10 ECM 5.417,2.042 6.021,2.417 0.604,0.375 10 C24

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.INSPECT ECM (SENSOR OUTPUT VOLTAGE)
a.
A286354C01
1.552,0.469 1.885,0.646 0.333,0.177 2.01,1.052 2.448,1.865 true 2.021,1.25 1.781,1.854 true 1.76,4.167 3.177,4.594 1.417,0.427 10 20 msec./DIV 0.49,3.229 1.052,3.49 0.563,0.26 10 GND 0.531,2.521 1.365,2.938 0.833,0.417 10 2 V/DIV 2.333,1.906 3,2.313 0.667,0.406 10 N2+ 1.583,0.479 2.25,0.885 0.667,0.406 10 C24 1.635,1.917 2.302,2.323 0.667,0.406 10 N2- 0.198,0.115 0.719,0.438 0.521,0.323 10 *a
*a Component with harness connected
(ECM)


Connect the oscilloscope probes to the N2+ terminal and N2- terminal of the ECM connector.


b.

Check the waveform when the engine is idling or cranking.

Terminal No. (Symbol) Tool Setting Condition
C24-8 (N2+) - C24-28 (N2-) 2 V/DIV, 20 msec./DIV Idling

OK:

The waveform exists in accordance with the engine speed.


HINT:
·

The waveforms shown in the illustration are at engine idling speed.

·

The oscilloscope waveform shown as an example does not include noise or chattering waveforms.

·

The waveform amplitudes differ slightly depending on the vehicle conditions.

·

Grounding failure of the shielded wire may cause noise in waveforms.



Result:
Proceed to
OK
NG




OK

NG

2.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)
a.

Inspect the camshaft position sensor.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C9-1 - C24-8 (N2+) Always Below 1 Ω
C9-2 - C24-28 (N2-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C9-1 or C24-8 (N2+) - Body ground Always 10 kΩ or higher
C9-2 or C24-28 (N2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the camshaft position sensor connector.

Result:
Proceed to
OK
NG




OK

4.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.
A286351E02
1.677,1.552 2.594,1.875 0.917,0.323 10 Clearance 2.438,1.823 3.354,2.146 0.917,0.323 10 Abnormal 0.333,1.813 1.25,2.135 0.917,0.323 10 Normal

Check the camshaft position sensor installation.

OK:

Sensor is installed correctly.


Result:
Proceed to
OK
NG




OK

5.CHECK CAMSHAFT (TIMING ROTOR)

NG

5.CHECK CAMSHAFT (TIMING ROTOR)
a.

Check the teeth of the timing rotor.

OK:

Timing rotor does not have any cracks or deformation.


Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

B

C