When the engine is cranked, a current flows from terminal ST of the ignition switch to terminal STA of the ECM (STA signal).
When signals STA, N and N2 are input to the ECM, transistor (Tr) turns ON, a current flows to the coil of the F/P (fuel pump) relay, the relay switch turns ON, and a current flows to the fuel pump. The fuel pump is then actuated.
While the N and N2 signals are generated (engine running), the ECM keeps Tr ON (fuel pump relay ON) and the fuel pump also keeps operating.
| *1 | Screw |
Start the engine (engine cranking operation).
Check that the fuel pulsation damper extrudes its screw.
Fuel pulsation damper extrudes its screw.
After the engine starts, check that the fuel pump operating sound occurs.
The fuel pump can be operated without the engine running.
Click hereEngine / Hybrid System>3SZ-VE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the F/P relay from the fuse block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | No battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
Reinstall the F/P relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connections | Switch Condition | Specified Conditions |
|---|---|---|
| E3-18 (FC1) - C24-7 (E01) | Ignition switch ON | 11 to 14 V |
| Tester Connections | Switch Condition | Specified Conditions |
|---|---|---|
| E3-17 (FC2) - C24-7 (E01) | Ignition switch ON | 11 to 14 V |
The fuel pump operates for 2 seconds after the ignition switch has been turned to ON. If the ignition switch was turned to ON with EFIT and E terminals of DLC3 connected, the fuel pump operates for 8 seconds. The voltage between FC and E01 decreases to below 2V in both cases.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel pump.
Click hereEngine / Hybrid System>3SZ-VE FUEL>FUEL PUMP>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the F/P relay from the fuse block.
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| F/P relay (5) - P1-4 (+) | Always | Below 1 Ω |
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| F/P relay (5) or P1-4 (+) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel pump connector.
Reinstall the F/P relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| P1-5 (E) - Body ground | Always | Below 1 Ω |
Reconnect the fuel pump connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the F/P relay from the fuse block.
Remove the EFI MAIN relay from the fuse block.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| F/P relay (3) - EFI MAIN relay (5) | Always | Below 1 Ω |
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| F/P relay (3) or EFI MAIN relay (5) - Body ground | Always | 10 kΩ or higher |
Reinstall the EFI MAIN relay.
Reinstall the F/P relay.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C
Disconnect the ECM connector.
Remove the F/P relay from the fuse block.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| E3-18 (FC1) - F/P relay (1) | Always | Below 1 Ω |
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| E3-17 (FC2) - F/P relay (1) | Always | Below 1 Ω |
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| E3-18 (FC1) or F/P relay (1) - Body ground | Always | 10 kΩ or higher |
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| E3-17 (FC2) or F/P relay (1) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector
Reinstall the F/P relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG