Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  P0141  Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)  


DESCRIPTION

HINT:

Sensor 2 refers to the sensor farthest from the engine assembly.


Refer to DTC P0130 (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>P0130).

HINT:

The ECM provides ON/OFF control circuit to adjust current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.


A262618E05
4.24,0.99 4.729,1.271 0.49,0.281 10 Heater 4.208,1.396 4.771,1.719 0.563,0.323 10 Sensor 0.406,0.844 1.344,1.167 0.938,0.323 10 From Battery 3.74,1.896 5.25,2.406 1.51,0.51 10 Heated Oxygen Sensor (Sensor2) 5.375,0.76 5.906,1.042 0.531,0.281 10 OXH2 5.375,1.146 5.813,1.427 0.438,0.281 10 OX2 5.375,1.656 5.771,1.906 0.396,0.25 10 E2 2.771,1.438 3.135,1.708 0.365,0.271 10 EFI 2.031,1 2.448,1.333 0.417,0.333 10 EFI 6.073,2.365 6.521,2.646 0.448,0.281 10 ECM 0.052,0.063 2.802,0.448 2.75,0.385 10 Reference (System Diagram of Sensor 2): 0.406,1.167 1.385,1.531 0.979,0.365 10 From IG SW

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0141 Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) Open or short in heated oxygen sensor heater circuit for 1.28 seconds or more (2 trip detection logic)
·

Open or short in heated oxygen sensor heater (sensor 2) circuit

·

Heated oxygen sensor heater (sensor 2)

·

ECM


Comes on DTC stored

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor (sensor 2).

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>HEATED OXYGEN SENSOR(w/ Rear Heated Oxygen Sensor)>INSPECTION

Result:
Proceed to
OK
NG




OK

2.INSPECT ECM (OXH2 VOLTAGE)

NG

2.INSPECT ECM (OXH2 VOLTAGE)
a.
A141531C19
1.448,0.979 1.792,1.208 0.344,0.229 0.677,0.979 1.021,1.208 0.344,0.229 1.917,2.542 1.646,1.833 true 0.469,2.604 0.844,1.656 true 1.906,2.594 2.188,2.885 0.281,0.292 10 E1 0.271,2.635 0.75,2.885 0.479,0.25 10 OXH2 0.229,0.177 0.573,0.51 0.344,0.333 10 *a 1.5,1.01 1.927,1.365 0.427,0.354 10 C24 0.719,1.01 1.229,1.365 0.51,0.354 10 C23
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connections Switch Condition Specified Conditions
C23-13 (OXH2) - C24-32 (E1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - HEATED OXYGEN SENSOR (SENSOR 2))
3.CHECK HARNESS AND CONNECTOR (ECM - HEATED OXYGEN SENSOR (SENSOR 2))
a.

Disconnect the ECM connector.


b.

Disconnect the heated oxygen sensor (sensor 2) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
For LHD
Tester Connections Condition Specified Conditions
C23-13 (OXH2) - C27-1 (OXH2) Always Below 1 Ω


Standard Resistance (Check for Open):
For RHD
Tester Connections Condition Specified Conditions
C23-13 (OXH2) - C27-1 (IREL) Always Below 1 Ω


Standard Resistance (Check for Short):
For LHD
Tester Connections Condition Specified Conditions
C23-13 (OXH2) or C27-1 (OXH2) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short):
For RHD
Tester Connections Condition Specified Conditions
C23-13 (OXH2) or C27-1 (IREL) - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor (sensor 2) connector.


e.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - EFI MAIN RELAY)
a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Remove the EFI MAIN relay from the fuse block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
For LHD
Tester Connections Condition Specified Conditions
C27-2 (+B) - EFI MAIN relay (5) Always Below 1 Ω


Standard Resistance (Check for Open):
For RHD
Tester Connections Condition Specified Conditions
C27-2 (ECHI) - EFI MAIN relay (5) Always Below 1 Ω


Standard Resistance (Check for Short):
For LHD
Tester Connections Condition Specified Conditions
C27-2 (+B) or EFI MAIN relay (5) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short):
For RHD
Tester Connections Condition Specified Conditions
C27-2 (ECHI) or EFI MAIN relay (5) - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor (sensor 2) connector.


e.

Reinstall the EFI MAIN relay.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C