Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  P0135  Oxygen (A/F) Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)  


DESCRIPTION

HINT:

Heated oxygen sensor refers to the sensor closest to the engine assembly.


Refer to DTC P0130 (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>P0130).

HINT:

The ECM provides ON/OFF control circuit to adjust current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.


A262618E04
4.24,0.99 4.771,1.302 0.531,0.313 10 Heater 4.208,1.385 4.844,1.667 0.635,0.281 10 Sensor 0.406,0.844 1.458,1.188 1.052,0.344 10 From Battery 3.74,1.844 5.208,2.396 1.469,0.552 10 Heated Oxygen Sensor (Sensor1) 5.375,0.76 6.219,1.125 0.844,0.365 10 OXH1 5.375,1.135 6,1.469 0.625,0.333 10 OX 5.375,1.635 5.979,1.969 0.604,0.333 10 E2 2.771,1.438 3.188,1.719 0.417,0.281 10 EFI 2.031,1 2.427,1.302 0.396,0.302 10 EFI 6.073,2.354 6.667,2.688 0.594,0.333 10 ECM 0.052,0.063 3.042,0.521 2.99,0.458 10 Reference (System Diagram of Sensor 1): 0.406,1.167 1.438,1.5 1.031,0.333 10 From IG SW

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0135 Oxygen (A/F) Sensor Heater Circuit Malfunction (Bank 1 Sensor 1) Open or short in heated oxygen sensor heater circuit for 1.28 seconds or more
(1 trip detection logic)
·

Open or short in heated oxygen sensor heater (sensor 1) circuit

·

Heated oxygen sensor heater (sensor 1)

·

ECM


Comes on DTC stored

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor (sensor 1).

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>HEATED OXYGEN SENSOR(w/o Rear Heated Oxygen Sensor)>INSPECTION

Result:
Proceed to
OK
NG




OK

2.INSPECT ECM (OXH1 VOLTAGE)

NG

2.INSPECT ECM (OXH1 VOLTAGE)
a.
A141531C03
1.448,0.99 1.823,1.188 0.375,0.198 1.927,2.51 1.646,1.833 true 2.521,2.531 1.74,1.542 true 1.885,2.552 2.365,2.917 0.479,0.365 10 E1 2.385,2.573 3.031,2.969 0.646,0.396 10 OXH1 0.229,0.177 0.688,0.615 0.458,0.438 10 *a 1.5,1.01 1.99,1.344 0.49,0.333 10 C24
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connections Switch Condition Specified Conditions
C24-3 (OXH1) - C24-32 (E1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - HEATED OXYGEN SENSOR)
3.CHECK HARNESS AND CONNECTOR (ECM - HEATED OXYGEN SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the heated oxygen sensor (sensor 1) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
For LHD
Tester Connections Condition Specified Conditions
C24-3 (OXH1) - C22-1 (HTR-) Always Below 1 Ω


Standard Resistance (Check for Open):
For RHD
Tester Connections Condition Specified Conditions
C24-3 (OXH1) - C26-1 (HTR-) Always Below 1 Ω


Standard Resistance (Check for Short):
For LHD
Tester Connections Condition Specified Conditions
C24-3 (OXH1) or C22-1 (HTR-) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short):
For RHD
Tester Connections Condition Specified Conditions
C24-3 (OXH1) or C26-1 (HTR-) - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor connector.


e.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - EFI MAIN RELAY)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Remove the EFI MAIN relay from the fuse block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
For LHD
Tester Connections Condition Specified Conditions
C22-2 (HTR+) - EFI MAIN relay (5) Always Below 1 Ω


Standard Resistance (Check for Open):
For RHD
Tester Connections Condition Specified Conditions
C26-2 (HTR+) - EFI MAIN relay (5) Always Below 1 Ω


Standard Resistance (Check for Short):
For LHD
Tester Connections Condition Specified Conditions
C22-2 (HTR+) or EFI MAIN relay (5) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short):
For RHD
Tester Connections Condition Specified Conditions
C26-2 (HTR+) or EFI MAIN relay (5) - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor (sensor 1) connector.


e.

Reinstall the EFI MAIN relay.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C