Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller (camshaft timing sprocket assembly). The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E47
2.563,4.573 2.844,4.271 2.844,4.271 3.604,4.271 false 3.177,4.823 3.323,5.052 3.323,5.052 3.854,5.052 false 4.479,0.813 5.708,1.313 1.229,0.5 10 VVT Sensor 4.479,1.323 6.688,1.844 2.208,0.521 10 Crankshaft Position Sensor 0.073,0.063 1.76,0.458 1.688,0.396 10 VVT System: 2.333,1.99 3.938,2.417 1.604,0.427 10 Target Valve Timing 2.333,1.292 4.156,1.865 1.823,0.573 10 Actual Valve Timing 2.688,2.698 3.76,3.146 1.073,0.448 10 Correction 2.823,3.208 3.604,3.646 0.781,0.438 10 ECM 1.604,3.76 4.219,4.188 2.615,0.427 10 Camshaft Timing Oil Control Valve 0.167,2.688 1.167,3.104 1,0.417 10 Duty Cycle 4.479,1.823 7.073,2.385 2.594,0.563 10 Manifold Absolute Pressure Sensor 4.479,2.854 7.156,3.375 2.677,0.521 10 Engine Coolant Temperature Sensor 4.479,2.344 6.354,2.771 1.875,0.427 10 Throttle Position Sensor 4.479,3.354 6.365,3.75 1.885,0.396 10 Vehicle Speed Sensor 0.375,4.271 1.979,4.656 1.604,0.385 10 Engine Oil Pressure 3.656,4.219 5.427,4.656 1.771,0.438 10 Camshaft Timing Gear 3.885,4.958 5.333,5.552 1.448,0.594 10 Intake Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

Advanced camshaft timing

Condition (a) or (b) continues after engine has warmed up and when engine speed 500 to 4000 rpm

(2 trip detection logic)

(a) Amount of valve timing change less than threshold

(b) Current valve timing fixed



·

Open or short in camshaft timing oil control valve assembly circuit

·

Valve timing

·

Camshaft timing oil control valve assembly

·

Camshaft timing oil control valve filter

·

Camshaft timing sprocket assembly

·

ECM


Comes on DTC stored
P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1)

Retarded camshaft timing

Condition (a) or (b) continues after engine has warmed up and when engine speed 500 to 4000 rpm

(2 trip detection logic)

(a) Amount of valve timing change less than threshold

(b) Current valve timing fixed



·

Open or short in camshaft timing oil control valve assembly circuit

·

Valve timing

·

Camshaft timing oil control valve assembly

·

Camshaft timing oil control valve filter

·

Camshaft timing sprocket assembly

·

ECM


Comes on DTC stored

PROCEDURE

1.CHECK VALVE TIMING
a.
A130143

Turn the crankshaft clockwise, to align the timing mark of the crankshaft pulley with the indicator of the timing chain cover.


b.
A130110

Check that the alignment marks of the camshaft timing sprocket are facing upward. If not, turn the crankshaft 1 revolution so they face upward.


c.

Check for looseness or a jumped tooth of the timing chain.

OK:

Alignment marks of the crankshaft pulley and camshaft pulley are aligned.


Result:
Proceed to
OK
NG




OK

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV OPERATION)

NG

ADJUST VALVE TIMING

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV OPERATION)
a.
A076968C01
0.156,0.115 0.729,0.552 0.573,0.438 10 *a
*a Component without harness connected
(Camshaft Timing Oil Control Valve Assembly)


Start the engine.


b.

Check the engine speed at check (1) and (2).

Check (1):

Disconnect the camshaft timing oil control valve assembly connector.

Check (2):

Apply battery voltage to the terminals of the camshaft timing oil control valve assembly.


Result:
Check (1) Check (2) Proceed To
Normal engine speed Rough idle or engine stall A
Condition other than above B



c.

Reconnect the camshaft timing oil control valve assembly connector.



A

3.INSPECT ECM (OCV SIGNAL)

B

6.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.INSPECT ECM (OCV SIGNAL)
a.
A286145C01
0.729,0.542 1.083,0.729 0.354,0.188 0.75,1.01 0.375,1.896 true 0.823,1.021 1.229,1.896 true 0.073,0.073 0.615,0.406 0.542,0.333 10 *a 0.771,0.552 1.313,0.885 0.542,0.333 10 C23 0.177,1.948 0.719,2.281 0.542,0.333 10 OCV+ 1.083,1.958 1.625,2.292 0.542,0.333 10 OCV- 0.708,2.417 2.76,2.771 2.052,0.354 10 OCV Signal Waveform 0.396,2.729 1.052,3.146 0.656,0.417 10 5 V/DIV 0.354,3.5 0.896,3.833 0.542,0.333 10 GND 1.635,4.302 2.885,4.542 1.25,0.24 10 1 msec./DIV
*a Component with harness connected
(ECM)


Inspect using an oscilloscope.


b.

During idling, check the waveform between the terminals of the ECM connector.

Terminal No. (Symbol) Tool Setting Condition
C23-6 (OCV+) - C23-5 (OCV-) 5 V/DIV, 1 msec./DIV Idling

OK:

The waveform exists accordance with the engine speed (Refer to the waveform in the illustration).


HINT:
·

The waveforms shown in the illustration are at engine idling speed.

·

The oscilloscope waveform shown as an example does not include noise or chattering waveforms.

·

The waveform amplitudes differ slightly depending on the vehicle conditions.



Result:
Result Proceed To
OK A
NG (for LHD) B
NG (for RHD) C




A

4.INSPECT OIL CONTROL VALVE FILTER (OCV FILTER)

B

C

4.INSPECT OIL CONTROL VALVE FILTER (OCV FILTER)
a.
A269351

Remove the OCV (Camshaft Timing Oil Control Valve) filter.


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



c.

Reinstall the OCV filter.

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPAIR OR REPLACE OIL CONTROL VALVE FILTER

5.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

OK

6.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.
A148713C01
0.135,0.094 0.75,0.521 0.615,0.427 10 *a
*a Component without harness connected
(Camshaft Timing Oil Control Valve Assembly)


Remove the camshaft timing oil control valve assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
1 - 2 20°C (68°F) 6.9 to 7.9 Ω



c.
A148714C01
0.104,0.073 0.729,0.521 0.625,0.448 10 *a 0.125,1.552 0.76,1.958 0.635,0.406 10 *b
*a Component without harness connected
(Camshaft Timing Oil Control Valve Assembly)
*b Valve Moves


Connect the positive battery terminal to terminal 1 and connect the negative battery terminal to terminal 2. Check the valve operation.

OK:

Valve moves quickly.



d.

Reinstall the camshaft timing oil control valve assembly.

Result:
Proceed to
OK
NG




OK

7.INSPECT CAMSHAFT TIMING SPROCKET ASSEMBLY

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

7.INSPECT CAMSHAFT TIMING SPROCKET ASSEMBLY
a.

Inspect the camshaft timing sprocket assembly.

Click hereEngine / Hybrid System>3SZ-VE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION

Result:
Proceed to
OK
NG




OK

8.CHECK FOR BLOCKAGE (OCV, OIL CHECK VALVE AND OIL HOLE)

NG

REPLACE CAMSHAFT TIMING SPROCKET ASSEMBLY

8.CHECK FOR BLOCKAGE (OCV, OIL CHECK VALVE AND OIL HOLE)
OK:

No blockage.


Result:
Result Proceed To
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

B

C