The fuel injectors are located in the intake port. They inject fuel into the cylinders in accordance with signals from the ECM.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C23-4 (#10) - C24-7 (E01) | Ignition switch ON | 11 to 14 V |
| C23-3 (#20) - C24-7 (E01) | Ignition switch ON | 11 to 14 V |
| C23-2 (#30) - C24-7 (E01) | Ignition switch ON | 11 to 14 V |
| C23-1 (#40) - C24-7 (E01) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| C24-7 (E01) - Body ground | Always | Below 1 Ω |
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>3SZ-VE FUEL>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI MAIN relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connections | Condition | Specified Conditions |
|---|---|---|
| 3 - 5 | No battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
Reinstall the EFI MAIN relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>3SZ-VE FUEL>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel injector assembly connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-2 (No. 1 injector) - C23-4 (#10) | Always | Below 1 Ω |
| C6-2 (No. 2 injector) - C23-3 (#20) | Always | Below 1 Ω |
| C7-2 (No. 3 injector) - C23-2 (#30) | Always | Below 1 Ω |
| C8-2 (No. 4 injector) - C23-1 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-2 (No. 1 injector) or C23-4 (#10) - Other terminals and body ground | Always | 10 kΩ or higher |
| C6-2 (No. 2 injector) or C23-3 (#20) - Other terminals and body ground | Always | 10 kΩ or higher |
| C7-2 (No. 3 injector) or C23-2 (#30) - Other terminals and body ground | Always | 10 kΩ or higher |
| C8-2 (No. 4 injector) or C23-1 (#40) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the fuel injector assembly connector.
Reconnect the ECM connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG