Home › Engine / Hybrid System › 3SZ-VE ENGINE MECHANICAL › ENGINE UNIT › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002969 3SZ-VE ENGINE MECHANICAL _0014999 ENGINE UNIT A

3SZ-VE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 11381A 3.INSTALL REAR ENGINE OIL SEAL

a.

Apply a light coat of MPgrease to the lip of a new oil seal.

NOTICE:

Keep the lip free of foreign matter.



b.

Using SST, install a new rear engine oil seal.

SST
09950-70010  (09951-07100)
09223-15020  

Protrusion of seal from edge:

0.5 mm (0.020 in.) or less


Depth of seal from edge:

1.0 mm (0.039 in.) or less


NOTICE:
·

Do not tap in the oil seal at an angle.

·

Keep the lip free of foreign matter.



A143179C04
2.333,0.5 2.677,0.26 false 2.729,0.177 3.417,0.552 0.688,0.375 10 SST 4.479,1.479 4.906,1.781 0.427,0.302 10 *b 4.167,0.542 4.74,0.896 0.573,0.354 10 *a 5.698,0.542 6.104,0.885 0.406,0.344 10 *1
*1 Cylinder Block side *a Press
*b 0.5 mm (0.0197 in.) - -



Hide 11381 4.INSTALL REAR ENGINE OIL SEAL RETAINER

A143059C04
0.865,1.823 1.323,2.177 0.458,0.354 10 *b 0.135,0.104 0.563,0.479 0.427,0.375 10 *a
*a Seal Width
*b 3.5 to 4.5 mm (0.1378 to 0.1772 in.)


a.

Apply seal packing to the rear engine oil seal retainer.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the engine rear oil seal retainer within 3 minutes, then tighten the bolts within 15 minutes of applying the seal packing.

·

Do not expose the seal packing to engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




b.

Install the rear engine oil seal retainer with the 4 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 83530 5.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 11432M 6.INSTALL CYLINDER BLOCK UNION

A137152

a.

Install a new O-ring onto the oil filter cylinder block union.


b.

Using a 12 mm socket hexagon wrench, install the cylinder block union.

Torque:
44 N*m (449 kgf*cm, 33 ft.*lbf)


Hide 15609 7.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

A137151

a.

Install a new O-ring, then install the oil filter bracket sub-assembly with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 15601 8.INSTALL OIL FILTER SUB-ASSEMBLY

A143061C04
2.698,0.25 2.344,0.885 true 2.76,0.125 3.229,0.448 0.469,0.323 10 SST 2.156,1.552 2.5,1.865 0.344,0.313 10 *a
*a 3/4 Turn


a.

Remove any dirt or foreign matter on the contact surface of the engine side.


b.

Apply a light coat of engine oil to the O-ring of a new oil filter.


c.

Install the O-ring by hand until it comes into contact with the contact surface.


d.

Using SST, tighten it by an additional 3/4 turn.

SST
09228-06501  

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13523 9.INSTALL CAMSHAFT TIMING GEAR OR SPROCKET

A137122

a.

Clamp No. 2 camshaft in a vise.


b.

Align the knock pin of No. 2 camshaft with the pin groove of the camshaft timing gear or sprocket, then install it with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 13520 11.INSTALL CAMSHAFT TIMING SPROCKET ASSEMBLY

A130146

a.

Align the knock pin of the camshaft and the pin groove of the sprocket, then install the sprocket onto the camshaft.


b.

Using the hexagonal lobe of the camshaft, install the camshaft timing sprocket assembly with the bolt.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 15708 13.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

Hide 13591 14.INSTALL TIMING CHAIN TENSION ARM

Hide 13545 17.INSTALL CHAIN TENSIONER PLUNGER

Hide 19315 18.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A143072

Install the No. 1 crankshaft position sensor plate with the D marks facing outward.


Hide 11302A 19.INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

Hide 11302 20.INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

Hide 15104 21.INSTALL OIL STRAINER SUB-ASSEMBLY

A137139

a.

Install a new O-ring onto the oil strainer sub-assembly.


b.

Install the oil strainer sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.
A143195

Install the oil pan baffle plate with the 7 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 12101 22.INSTALL OIL PAN SUB-ASSEMBLY

A143077C04
0.719,2.323 0.875,2.708 true 1.427,0.813 1.531,0.531 false 1.073,1.594 0.76,2.156 true 1.135,1.469 1.469,1.771 0.333,0.302 10 A 1.594,2.958 1.979,3.281 0.385,0.323 10 *a 1.469,0.344 2.156,0.646 0.688,0.302 10 *b (*e) 0.875,2.719 1.51,3.073 0.635,0.354 10 *b (*f) 0.406,3.063 0.75,3.375 0.344,0.313 10 *d 0.417,0.229 0.813,0.573 0.396,0.344 10 *c
*a Seal Packing
*b Digmeter
*c 18 mm (0.7087 in.)
*d 17 mm (0.6693 in.)
*e 3.0 to 4.0 mm (0.1181 to 0.1575 in.)
*f 1.3 to 1.5 mm (0.0512 to 0.0591 in.)


a.

Apply seal packing to the oil pan sub-assembly.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Make sure that seal packing does not come into contact with area A in the illustration.

·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes, and tighten the bolts within 15 minutes of applying of the seal packing.

·

Do not expose the seal packing to engine oil for at least 2 hours after the installation.

·

Do not start the engine for at least 2 hours after the installation.

·

Do not begin or finish applications of seal packing near the engine front chain cover or the rear oil seal retainer. Any joints in the seal packing should be on the intake or exhaust sides of the cylinder block.




b.
A137137C04
0.615,0.781 0.865,1.104 0.25,0.323 10 A 0.385,2.219 0.646,2.531 0.26,0.313 10 D 0.375,1.292 0.656,1.688 0.281,0.396 10 D 1.125,0.688 1.417,1.063 0.292,0.375 10 A 2.125,0.688 2.385,1.042 0.26,0.354 10 A 2.604,0.76 2.927,1.167 0.323,0.406 10 A 3.031,0.948 3.292,1.292 0.26,0.344 10 B 3.188,1.219 3.427,1.625 0.24,0.406 10 C 3.198,2.229 3.427,2.677 0.229,0.448 10 C 0.604,2.531 0.906,2.865 0.302,0.333 10 C 3.01,2.563 3.302,2.958 0.292,0.396 10 B 2.573,2.583 2.896,3.01 0.323,0.427 10 A 2.094,2.615 2.385,2.99 0.292,0.375 10 A 1.198,2.615 1.51,2.917 0.313,0.302 10 A
V100135

Engine Front


Install the oil pan sub-assembly with the 11 bolts and 3 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

for bolt A

42 N*m (428 kgf*cm, 31 ft.*lbf)

for bolt B

8.5 N*m (87 kgf*cm, 75 in.*lbf)

for nut C

8.5 N*m (87 kgf*cm, 75 in.*lbf)

for bolt D


HINT:

Each bolt length is as follows.

A: 18 mm (0.787 in.)

B: 25 mm (0.984 in.)

D: 20 mm (0.709 in.)



Hide 15330 26.INSTALL CAM TIMING OIL CONTROL VALVE ASSEMBLY

A143078

a.

Install the camshaft timing oil control valve sub-assembly with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 11201 27.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12108 28.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.


Hide 19100P 29.INSTALL SPARK PLUG

a.

Using a spark plug wrench, install the 4 spark plugs.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 30.INSTALL ENGINE HANGERS

a.

Install the engine hangers with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)