Home › Engine / Hybrid System › K3-VE ENGINE MECHANICAL › ENGINE › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002970 K3-VE ENGINE MECHANICAL _0015002 ENGINE G

K3-VE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that the air cleaner filter is not excessively damaged or oily. If necessary, replace the air cleaner filter.

HINT:
·

If there is any dirt or a blockage in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or a blockage remains even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.


Hide 7.INSPECT IGNITION TIMING

NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transmission should be in neutral or park.



a.

Warm up and stop the engine.


b.

When using the intelligent tester or Techstream: Check the ignition timing.

i.

Connect the intelligent tester or Techstream to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the intelligent tester or Techstream on.


iv.

Enter the following menus: Powertrain / Engine / Data List / IGN Advance.

Ignition timing:

-5 to 15° BTDC


Powertrain > Engine > Data List
Tester Display
IGN Advance
50003 206 34
HINT:

Refer to the intelligent tester or Techstream operator's manual for further details.



v.

Check that the ignition timing advances immediately when the engine speed is increased.


vi.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine > Active Test
Tester Display
Connect the TC and TE1
50004 206 8

vii.

Monitor IGN Advance of the Data List.

Ignition timing:

4 to 8° BTDC


NOTICE:

When checking the ignition timing, the transmission should be in neutral or park.



viii.

Enter the following menus: Connect the TC and TE1 / OFF.


ix.

Turn the ignition switch off.


x.

Disconnect the intelligent tester or Techstream from the DLC3.



c.

When not using the intelligent tester or Techstream:

i.
A169891C05
1.615,1.646 1.896,1.969 true 1.573,1.031 1.573,0.719 true 0.927,1.052 1.031,1.208 0.104,0.156 10 1 1.135,1.052 1.24,1.208 0.104,0.156 10 2 1.344,1.052 1.448,1.208 0.104,0.156 10 3 1.552,1.052 1.656,1.208 0.104,0.156 10 4 1.75,1.052 1.854,1.208 0.104,0.156 10 5 1.948,1.052 2.052,1.208 0.104,0.156 10 6 2.156,1.052 2.26,1.208 0.104,0.156 10 7 2.365,1.052 2.469,1.208 0.104,0.156 10 8 0.927,1.458 1.031,1.615 0.104,0.156 10 9 1.094,1.458 1.271,1.615 0.177,0.156 10 10 1.302,1.458 1.479,1.615 0.177,0.156 10 11 1.51,1.458 1.688,1.615 0.177,0.156 10 12 1.708,1.458 1.885,1.615 0.177,0.156 10 13 1.917,1.458 2.094,1.615 0.177,0.156 10 14 2.115,1.458 2.292,1.615 0.177,0.156 10 15 2.323,1.458 2.5,1.615 0.177,0.156 10 16 1.969,1.958 2.552,2.135 0.583,0.177 10 EFIT 0.156,0.156 0.656,0.51 0.5,0.354 10 *a 1.531,0.51 1.99,0.885 0.458,0.375 10 E
*a Front view of DLC3


Using SST, connect terminals 12 (EFIT) and 4 (E) of the DLC3.

SST
09843-18040  

NOTICE:
·

Be sure to connect the terminals correctly. Failure to do this can damage the engine.




ii.
A268773C01
0.125,2.302 0.604,2.667 0.479,0.365 12 B: 0.125,0.063 0.563,0.479 0.438,0.417 12 A:
*A for RHD
*B for LHD


Connect the clip of the timing light to the wire harness.

NOTICE:

Use a timing light that detects the primary signal.



iii.
A261157

Inspect the ignition timing at idle.

Ignition timing:

4 to 8° BTDC


NOTICE:

When checking the ignition timing, the transmission should be in neutral or park.


HINT:

Run the engine at 1000 to 1300 rpm for 5 seconds, and check that the engine speed returns to the idling speed.



iv.

Disconnect terminals 12 (EFIT) and 4 (E) of the DLC3.


v.

Inspect the ignition timing at idle.

Ignition timing:

-5 to 15° BTDC



vi.
A143146C03
2.708,1.625 3.135,2 0.427,0.375 10 *c 1.677,1.625 2.281,1.958 0.604,0.333 10 *b 0.594,1.625 1.115,1.958 0.521,0.333 10 *a
*a Standard +2
*b Standard
*c Standard -2


Check that the ignition timing advances immediately when the engine speed is increased.


vii.

Remove the timing light.



Hide 8.INSPECT ENGINE IDLE SPEED

NOTICE:
·

Turn all electrical systems and the A/C off.

·

Inspect the idle speed with the cooling fans off.

·

When checking the idle speed, the transmission should be in neutral or park.



a.

Warm up and stop the engine.


b.

Connect the intelligent tester or Techstream to the DLC3.


c.

Start the engine and run it at idle.


d.

Turn the intelligent tester or Techstream on.


e.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

HINT:

Refer to the intelligent tester or Techstream operator's manual for further details.


Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 206 32

f.

Inspect the engine idle speed.

Idling speed:

750 rpm



g.

Turn the ignition switch off.


h.

Disconnect the intelligent tester or Techstream from the DLC3.


Hide 9.INSPECT COMPRESSION

a.

Check for DTCs. (Click here Engine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR)

HINT:

If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.


Powertrain > Engine > Trouble Codes
50001 206

b.

Warm up and stop the engine.


c.

Remove the 4 spark plugs. (Click here Engine / Hybrid System>K3-VE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL)

NOTICE:

Ensure that foreign objects do not enter the intake manifold.



d.

Disconnect the 4 fuel injector connectors.


e.
A261712

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1470 kPa (15.0 kgf/cm2, 213 psi)


Minimum pressure:

1079 kPa (11.0 kgf/cm2, 156 psi)


Difference between each cylinder:

147 kPa (1.5 kgf/cm2, 21 psi) or less


NOTICE:
·

Use a fully-charged battery so that the engine speed can be increased to 330 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression in as a short time as possible.




iii.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, and then inspect it again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.





f.

Connect the 4 fuel injector connectors.



h.

Clear the DTC. (Click here Engine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR)

Powertrain > Engine > Clear DTCs
50002 206

i.

Check for DTCs. (Click here Engine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR)

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Powertrain > Engine > Clear DTCs
50002 206

Hide 10.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with local regulations.


a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.


d.

Immediately check the CO/HC concentration while idling.

CO concentration at idle:

0 to 0.2 %


HC concentration at idle:

Applicable local regulations


If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

i.

Check the heated oxygen sensor operation.


ii.

See the table below for possible causes of mulfunctions, then inspect and repair the applicable parts if necessary.

CO HC Problem Possible Cause
Normal High Rough idle
1.

Faulty ignition:

·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leakage from intake and exhaust valves

4.

Leakage from cylinders


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body

·

ISCV

·

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element

2.

Plugged PCV valve

3.

Faulty EFI system:

·

Faulty pressure regulator

·

Faulty engine coolant temperature sensor

·

Faulty mass air flow meter

·

Faulty ECM

·

Faulty injectors

·

Faulty throttle position sensor