Home › Engine / Hybrid System › K3-VE COOLING › COOLING FAN SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002977 K3-VE COOLING _0015044 COOLING FAN SYSTEM J

K3-VE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


TECHNICAL DESCRIPTION

To control the cooling fan, the ECM turns on or off the cooling fan relay based on the engine coolant temperature, air conditioning switch, refrigerant pressure, engine speed and vehicle speed signals.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK WIRE HARNESS AND CONNECTOR (RAD RELAY VOLTAGE)
a.
A265843C02
0.104,0.115 0.469,0.427 0.365,0.313 10 *1 2.063,1.177 2.427,1.49 0.365,0.313 10 *2
*1 Engine Room Relay Block
*2 RAD Relay


Remove the RAD relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RAD relay terminal 3 - Body ground Always 11 to 14V



c.

Reinstall the RAD relay.

Result:
Proceed to
OK
NG




OK

2.CHECK WIRE HARNESS AND CONNECTOR (AM2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

2.CHECK WIRE HARNESS AND CONNECTOR (AM2 VOLTAGE)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E28-5 (AM2) - Body ground Always 11 to 14V



c.

Reconnect the ignition or starter switch assembly connector.

Result:
Proceed to
OK
NG




OK

3.INSPECT RAD RELAY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT RAD RELAY
a.

Inspect the RAD relay.

Click hereEngine / Hybrid System>K3-VE COOLING>RELAY>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

4.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPLACE RAD RELAY

4.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>K3-VE STARTING>IGNITION SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

5.CHECK WIRE HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - RAD RELAY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

5.CHECK WIRE HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - RAD RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the RAD relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E28-6 (IG2) - RAD relay terminal 2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E28-6 (IG2) or RAD relay terminal 2 - Body ground Always 10 kΩ or higher



d.

Reinstall the RAD relay.


e.

Reconnect the ignition or starter switch assembly connector.

Result:
Proceed to
OK
NG




OK

6.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

6.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 - Body ground Always Below 1 Ω



c.

Reconnect the cooling fan motor connector.

Result:
Proceed to
OK
NG




OK

7.INSPECT COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

7.INSPECT COOLING FAN MOTOR
a.

Inspect the cooling fan motor

Click hereEngine / Hybrid System>K3-VE COOLING>COOLING FAN MOTOR>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

8.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - RAD RELAY)

NG

8.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - RAD RELAY)
a.

Disconnect the cooling fan motor connector.


b.

Remove the RAD relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A6-2 - RAD relay terminal 5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A6-2 or RAD relay terminal 5 - Body ground Always 10 kΩ or higher



d.

Reinstall the RAD relay.


e.

Reconnect the cooling fan motor connector.

Result:
Proceed to
OK
NG




OK

9.CHECK WIRE HARNESS AND CONNECTOR (RAD RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

9.CHECK WIRE HARNESS AND CONNECTOR (RAD RELAY - ECM)
a.

Remove the RAD relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E3-16 (FAN) - RAD relay terminal 1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E3-16 (FAN) or RAD relay terminal 1 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the RAD relay.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR