Home › Drivetrain › A4Q AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT › 2011.11–2015.08
RM19Y0E _52 Drivetrain _002983 A4Q AUTOMATIC TRANSMISSION / TRANSAXLE _0015086 AUTOMATIC TRANSMISSION UNIT A

A4Q AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 35103 1.REMOVE TRANSMISSION OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 35108C 3.REMOVE NO. 1 BREATHER PLUG

a.
C153940C02
2.844,0.188 2.177,0.125 true 2.229,0.583 1.365,0.469 true 1.99,0.042 2.5,0.479 0.51,0.438 10 *2 1.167,0.385 1.74,0.802 0.573,0.417 10 *1
*1 No. 1 Breather Plug
*2 No. 2 Breather Plug


Remove the No. 2 breather plug and No. 1 breather plug.


Hide 35578B 4.REMOVE TRANSMISSION CONTROL CABLE BRACKET

a.
C153941

Remove the 2 bolts and transmission control cable bracket.


b.
C153942C02
0.906,0.594 1.094,1.198 true 1.042,1.219 1.552,1.688 0.51,0.469 10 *1
*1 Protective Tape


Using a screwdriver, disconnect the connector of the park/neutral position switch from the switch harness clamp.

HINT:

Tape up the screwdriver tip before use.



Hide 89413G 5.REMOVE TRANSMISSION REVOLUTION SENSOR

a.
C153943C03
2.135,0.823 1.573,0.948 true 0.542,0.896 0.323,1.031 false 1.375,0.875 1.917,1.385 0.542,0.51 10 *2 0.167,1.042 0.615,1.458 0.448,0.417 10 *1
*1 Transmission Revolution Sensor (Input Speed Sensor)
*2 Transmission Revolution Sensor (Output Speed Sensor)


Remove the bolt and the transmission revolution sensor (Output speed sensor).


b.

Remove the bolt and the transmission revolution sensor (Input speed sensor).


c.

Remove the 2 O-ring from the transmission revolution sensors.


Hide 84540 7.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136924

Remove the bolt and pull out the park/neutral position switch assembly.

HINT:

Make sure that the manual valve lever sub-assembly has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever sub-assembly.



Hide 35000 8.FIX AUTOMATIC TRANSMISSION ASSEMBLY

a.
C153944

Install the automatic transmission assembly on the overhaul attachment.


Hide 35106D 9.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

Hide 35409D 12.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

Hide 35824 14.REMOVE BRAKE CYLINDER SEAL

a.
C154577C03
1.438,0.719 1.646,1.146 true 1.594,1.167 1.781,1.333 0.188,0.167 10 *1
*1 Brake Cylinder Seal


Remove the brake cylinder seal.


b.

Remove the bolt, plate and spring.


Hide 35561 15.REMOVE MANUAL VALVE IDLER SHAFT

a.
C153945

Remove the manual valve idler shaft and manual valve idler plug.


Hide 35056 16.REMOVE PARKING LOCK LEVER SUB-ASSEMBLY

a.
C153946

Using a pin punch and a hammer, remove the slotted spring pin.

NOTICE:

When removing the pin, do not drop it into the transmission case.



b.

Remove the control shaft.


c.

Remove the parking lock lever sub-assembly and parking lock rod sub-assembly.


Hide 35104F 17.REMOVE TRANSMISSION CASE OIL SEAL

a.
C153947C02
1.51,0.938 1.5,1.563 true 1.396,1.635 1.875,2.031 0.479,0.396 10 *1
*1 Protective Tape


Using a screwdriver, remove the transmission case oil seal from the transmission case.

HINT:

Tape up the screwdriver tip before use.



Hide 35108R 18.REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

a.
C153948N01
1.729,1.552 2.083,1.698 false 2.115,1.625 2.823,2.052 0.708,0.427 10 SST

Using SST, remove the automatic transmission extension housing oil seal.

SST
09308-10010  


Hide 35108 19.REMOVE EXTENSION HOUSING SUB-ASSEMBLY

a.
C153949C03
2.01,0.448 2.635,0.302 true 2.646,0.188 3.167,0.594 0.521,0.406 10 *1
*1 No. 2 Engine Hanger


Remove the 10 bolts and No. 2 engine hanger.

HINT:

Be sure to remove the bolts evenly, removing opposing bolts in sequence.



b.
C153950C02
0.865,0.167 1.188,0.875 true 3.135,0.25 2.917,1.063 true 0.688,0.021 1.229,0.479 0.542,0.458 10 *a 3.156,0.125 3.427,0.677 0.271,0.552 10 *a
*a Rib


Using a plastic hammer, lightly tap the 2 ribs on the extension housing sub-assembly to remove the extension housing sub-assembly.


Hide 35847C 20.REMOVE TRANSMISSION LUBE APPLY TUBE

a.
C153951

Remove the transmission lube apply tube.


Hide 21.REMOVE OUTPUT SHAFT SUB-ASSEMBLY

a.
C153952

Remove the output shaft sub-assembly.


Hide 35108B 22.REMOVE RADIAL BALL BEARING

a.
C153953N02
2.444,0.642 2.737,0.788 0.292,0.145 10 SST 2.123,0.704 2.41,0.733 false

Using SST, remove the radial ball bearing.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04020, 09955-04061, 09957-04010, 09958-04011)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 35557 23.REMOVE PARKING LOCK PAWL

a.
C153954

Remove the torsion spring, parking lock pawl shaft and parking lock pawl.


Hide 35505 24.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

a.
C153955

Remove the 3 bolts, parking lock pawl cam support and manual valve lever sub-assembly.


Hide 35301 25.INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY

a.
C153956

Using a dial indicator, measure the input shaft end play.

Standard end play:

0.26 to 0.88 mm (0.0102 to 0.0346 in.)



Hide 35301 26.REMOVE FRONT OIL PUMP BODY SUB-ASSEMBLY

a.
C153957

Remove the 7 bolts.

HINT:

Be sure to remove the bolts evenly, removing opposing bolts in sequence.



b.
C153958N01
2.031,0.667 2.76,0.698 false 2.792,0.615 3.344,1.073 0.552,0.458 10 SST

Using SST, remove the front oil pump body sub-assembly.

SST
09820-00021  


Hide 35610 27.REMOVE FRONT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C153959

Remove the front multiple disc clutch assembly with rear multiple disc clutch assembly.


Hide 35650 28.REMOVE REAR MULTIPLE DISC CLUTCH ASSEMBLY

a.
C153960C02
2.656,0.177 3.073,0.615 false 1.708,1.167 1.708,1.354 1.708,1.354 1.969,1.354 false 1.969,1.354 1.969,1.094 false 1.833,1.135 1.833,1.583 false 2.49,0.083 2.896,0.51 0.406,0.427 10 *1 1.74,1.625 2.26,2.042 0.521,0.417 10 *2
*1 Thrust Needle Roller Bearing
*2 Input Shaft Oil Seal Ring


Remove the rear multiple disc clutch assembly from the front multiple disc clutch assembly.


b.

Remove the thrust needle roller bearing from the front multiple disc clutch assembly.


c.

Remove the 3 input shaft oil seal rings from the rear multiple disc clutch assembly.


Hide 35610 29.INSPECT FRONT MULTIPLE DISC CLUTCH ASSEMBLY

Hide 35633B 30.REMOVE NO. 1 CLUTCH DISC

a.
C270744C01
1.833,0.344 2.156,0.188 true 2.208,0.104 2.521,0.302 0.313,0.198 10 false *1
*1 Protective Tape


Using a screwdriver, remove the hole snap ring.

HINT:

Tape up the screwdriver tip before use.



b.
C270745

Remove the reverse clutch flange, 2 No. 1 clutch discs and 2 No. 1 clutch plates.


Hide 35633F 32.REMOVE NO. 2 CLUTCH DISC

a.
C270746C01
1.844,0.354 2.146,0.177 true 2.188,0.094 2.5,0.292 0.313,0.198 10 false *1
*1 Protective Tape


Using a screwdriver, remove the hole snap ring.

HINT:

Tape up the screwdriver tip before use.



b.
C270747

Remove the forward clutch flange, 4 No. 2 clutch discs and 4 No. 2 clutch plates.


Hide 35650 34.INSPECT REAR MULTIPLE DISC CLUTCH ASSEMBLY

Hide 35673 35.REMOVE REAR CLUTCH DISC

a.
C270748C01
1.802,0.365 2.135,0.271 true 2.177,0.177 2.49,0.375 0.313,0.198 10 false *1
*1 Protective Tape


Using a screwdriver, remove the hole snap ring.

HINT:

Tape up the screwdriver tip before use.



b.
C270749

Remove the 6 rear clutch flanges, 6 rear clutch discs, No. 3 clutch plate and rear clutch cushion plate.


Hide 35708J 37.REMOVE INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C153961C03
1.604,0.219 2.125,0.156 true 2.156,0.073 2.646,0.49 0.49,0.417 10 *1
*1 Thrust Needle Roller Bearing


Remove the intermediate shaft sub-assembly.


b.

Remove the thrust needle roller bearing from the intermediate shaft sub-assembly.


Hide 35631H 38.REMOVE FORWARD CLUTCH HUB

a.
C153962C03
1.688,0.188 2.156,0.146 false 2.177,0.042 2.365,0.24 0.188,0.198 10 *1
*1 Thrust Needle Roller Bearing


Remove the forward clutch hub.


b.

Remove the thrust needle roller bearing from the forward clutch hub.


Hide 35706U 39.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C153963C03
0.698,0.302 2.271,0.229 2.271,0.229 0.667,1.552 true 2.333,0.115 2.813,0.51 0.479,0.396 10 *1
*1 Thrust Needle Roller Bearing


Remove the planetary sun gear sub-assembly.


b.

Remove the 2 thrust needle roller bearings from the front planetary sun gear sub-assembly.


Hide 35709L 40.REMOVE REAR PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C153964

Remove the rear planetary sun gear sub-assembly.


Hide 41.MEASURE BRAKE DISC END PLAY

a.
C153965C03
2.302,1.74 2.167,1.927 true 2.094,1.021 1.74,0.208 true 2.021,1.938 2.417,2.177 0.396,0.24 10 *1 1.583,0.063 2.115,0.49 0.531,0.427 10 *2
*1 1st and Reverse Brake
*2 2nd and 4th Brake


Using a feeler gauge, measure the 1st and reverse brake and 2nd and 4th brake end play.

Standard end play:
1st and reverse brake:

0.65 to 1.13 mm (0.0256 to 0.0445 in.)

2nd and 4th brake:

1.07 to 1.52 mm (0.0421 to 0.0598 in.)


HINT:

If the measured end play fails to conform to the specified value above, select a snap ring.



Hide 35681 42.REMOVE NO. 1 BRAKE DISC

a.
C153966

Using snap ring pliers, remove the hole snap ring.


b.
C153967

Remove the 2 No. 1 brake flanges, 3 brake plates and 4 No. 1 brake discs.


Hide 35624E 43.REMOVE 2ND AND 4TH BRAKE PISTON

a.
C153968

Using snap ring pliers, remove the hole snap ring.


b.
C153969C03
2.104,1.021 2.375,1.01 false 1.323,0.26 1.083,0.188 false 1.271,1.615 1.01,1.563 false 0.875,0.094 1.406,0.531 0.531,0.438 10 *1 0.781,1.458 1.313,1.927 0.531,0.469 10 *3 2.385,0.896 2.927,1.385 0.542,0.49 10 *2
*1 2nd and 4th Brake Piston Return Spring Seat
*2 2nd and 4th Brake Piston Return Spring
*3 2nd and 4th Brake Piston


Remove the 2nd and 4th brake piston return spring seat, 2nd and 4th brake piston return spring, 2nd and 4th brake piston and 2nd and 4th brake cylinder.


c.
C153970

Apply compressed air to the oil hole to remove the 2nd and 4th brake piston from the 2nd and 4th brake cylinder.

HINT:

When the piston can not be removed as it is slanted, either blow the air again while holding down the protruding side by hand or remove the piston using needle nose pliers with tape on the tip.



d.
C153971

Using a screwdriver, remove the 2 O-rings from the 2nd and 4th brake piston.


Hide 35720L 44.REMOVE PLANETARY GEAR ASSEMBLY

a.
C153972

Remove the planetary gear assembly and the 1 way clutch assembly from the transmission case.


Hide 35790E 45.REMOVE 1 WAY CLUTCH ASSEMBLY

a.
C153973C02
1.177,0.667 0.75,0.677 false 0.563,0.594 1.042,1.052 0.479,0.458 10 *1
*1 1 way clutch assembly


Remove the 1 way clutch assembly from the planetary gear assembly.


Hide 35666B 46.REMOVE BRAKE CLUTCH DISC

a.
C153974

Using snap ring pliers, remove the hole snap ring.


b.
C153975

Remove the brake flange, 5 brake clutch discs and 5 brake plates.


Hide 35740 47.REMOVE FRONT PLANETARY RING GEAR ASSEMBLY

a.
C153976C02
1.833,0.375 2.49,0.281 true 2.5,0.188 2.906,0.625 0.406,0.438 10 *1
*1 Thrust Needle Roller Bearing


Remove the thrust needle roller bearing from the front planetary ring gear assembly.


b.
C153977

Tap on the circumference of the front planetary ring gear assembly with a plastic hammer to remove the front planetary ring gear assembly.

NOTICE:

In case that the front planetary ring gear assembly is dropped, hold it with hand while removal.



Hide 35775F 48.REMOVE RADIAL BALL BEARING

a.
C153978

Remove the radial ball bearing from the transmission case.

HINT:

If any difficulty is encountered in removing the radial ball bearing, remove it by applying a light impact from the inside of the transmission case, using a brass bar and a plastic hammer.



Hide 35623H 49.REMOVE 1ST AND REVERSE BRAKE PISTON

a.
C267379C02
0.802,0.688 0.417,0.198 true 1.729,2.042 1.417,1.625 true 2.865,1.396 2.771,1 true 2.313,1.281 2.052,0.208 2.052,0.208 2.49,1.042 true 0.135,0.083 0.729,0.427 0.594,0.344 10 SST 2.75,1.438 3.344,1.781 0.594,0.344 10 SST 1.771,1.969 2.438,2.177 0.667,0.208 10 SST 1.948,0.052 2.375,0.354 0.427,0.302 10 *a
*a Deformation


Place SST on the 1st and reverse brake piston return spring seat and compress the 1st and reverse brake piston return spring.

SST
09351-87201  
09351-97201  

HINT:

To prevent deformation, be sure to stop tightening the SST when the spring has been lowered 1 to 2 mm (0.04 to 0.08 in.) from the snap ring installation groove.



b.
C153980

Using snap ring pliers, remove the hole snap ring.


c.

Remove the 1st and reverse brake piston return spring seat and 1st and reverse brake piston return spring.


d.
C153981C02
3.115,2.073 3.292,2.073 false
V100135

Compressed Air


Apply compressed air (392 to 784 kPa, 4 to 8 kgf/cm2, 57 to 114 psi) into the transmission case to remove the 1st and reverse brake piston.

NOTICE:

Be careful to avoid splashing oil when applying compressed air.



Hide G1406 50.REMOVE TRANSMISSION SOLENOID CONNECTOR SUB-ASSEMBLY

a.
C153982

Remove the bolt and transmission solenoid connector sub-assembly.


b.

Remove the O-ring.