Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1251/51  Open in Pump Motor Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1251/51 Open in Pump Motor Circuit Either condition is met:
1.

ABS pump motor does not operate properly.

2.

Open in ABS pump motor circuit continues for at least 2 seconds.


·

Brake actuator assembly (Ground circuit)

·

Brake actuator assembly (Motor circuit)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC / Active Test.

ABS/VSC
Tester Display Test Part Control Range Diagnostic Note
ABS Motor Relay ABS motor relay ON / OFF The operating sound of the motor can be heard.


f.

Check the operating sound of the ABS motor relay when operating it with the intelligent tester.

Result:
Result Proceed to
The operating sound is not heard A
The operating sound is heard B




A

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

B

3.RECONFIRM DTC
2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.
C248686C06
1.458,0.635 1.948,0.927 0.49,0.292 0.594,0.708 0.938,0.708 0.938,0.708 0.938,1.51 true 0.594,2.75 0.938,2.75 0.938,2.75 0.938,1.948 true 2.479,2.646 2.479,1.948 true 0.135,0.094 0.635,0.469 0.5,0.375 10 *a 1.583,0.698 2.24,1.229 0.656,0.531 10 B10 0.135,2.667 0.875,3.094 0.74,0.427 10 GND2 2.292,2.667 3,3.208 0.708,0.542 10 +BM 0.135,0.635 0.865,0.979 0.729,0.344 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B10-1 (GND1) - Body ground Always Below 1 Ω
B10-13 (GND2) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
B10-24 (+BM) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay is in the skid control ECU (brake actuator assembly). Therefore, the ABS motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the skid control ECU (brake actuator assembly).


a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B