Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0226/52  SFR Solenoid  C0236/54  SFL Solenoid  C0246/56  SRR Solenoid  C0256/58  SRL Solenoid  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C0226/52 SFR Solenoid Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid circuit

·

Brake actuator assembly


C0236/54 SFL Solenoid Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid circuit

·

Brake actuator assembly


C0246/56 SRR Solenoid Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid circuit

·

Brake actuator assembly


C0256/58 SRL Solenoid Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid circuit

·

Brake actuator assembly



WIRING DIAGRAM

C248683E02
3.979,1.063 5.948,1.729 1.969,0.667 10 ABS SOLENOID RELAY 2.604,1.052 3.208,1.406 0.604,0.354 10 +BS 1.344,1.313 2.396,1.76 1.052,0.448 10 ABS NO. 2 0.115,1.313 1.229,1.979 1.115,0.667 10 from Battery 2.385,1.052 2.833,1.396 0.448,0.344 10 12 2.615,3 3.458,3.49 0.844,0.49 10 GND1 2.615,3.854 3.333,4.281 0.719,0.427 10 GND2 2.458,2.906 2.885,3.271 0.427,0.365 10 1 2.385,3.75 2.708,4.073 0.323,0.323 10 13 3.76,5.313 5.521,5.958 1.76,0.646 10 SKID CONTROL ECU 3.031,6.021 5.688,6.677 2.656,0.656 10 BRAKE ACTUATOR ASSEMBLY 3.031,5.854 3.5,6.229 0.469,0.375 10 B10 5.979,0.896 6.76,1.375 0.781,0.479 10 SRLR 5.979,1.417 6.719,1.917 0.74,0.5 10 SRLH 5.979,1.917 6.688,2.344 0.708,0.427 10 SFRR 5.979,2.427 6.75,2.917 0.771,0.49 10 SFRH 5.979,2.917 6.708,3.375 0.729,0.458 10 SFLR 5.979,3.427 6.76,3.938 0.781,0.51 10 SFLH 5.979,3.927 6.667,4.354 0.688,0.427 10 SRRR 5.979,4.438 6.688,4.917 0.708,0.479 10 SRRH

CAUTION / NOTICE / HINT

NOTICE:

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly). Therefore, the solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.


a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B