Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"Engine" is not displayed on the "CAN Bus Check" screen of the intelligent tester or Techstream (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table" (See page (Click here)).


·

Power source circuit of ECM

·

ECM main line or connector

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C243546E03
5.073,3.292 5.594,3.729 0.521,0.438 10 +B1 5.156,4.094 5.521,4.448 0.365,0.354 10 E1 5.406,4.083 5.917,4.438 0.51,0.354 10 C24 5.49,3.115 5.792,3.438 0.302,0.323 10 7 5.448,3.875 5.792,4.177 0.344,0.302 10 32 6.188,3.292 6.99,3.979 0.802,0.688 10 to EFI MAIN Relay 5.406,3.292 5.875,3.708 0.469,0.417 10 C23 4.594,5.021 5.688,5.552 1.094,0.531 10 Trouble Area 4,2.063 4.677,2.573 0.677,0.51 10 DLC3 4.302,4.615 4.917,5.115 0.615,0.5 10 ECM 1.375,4.615 2.896,5.354 1.521,0.74 10 CAN NO. 1 JUNCTION CONNECTOR* 1.24,2 2.042,2.49 0.802,0.49 10 * : for A/T 0.115,0.063 2.354,0.49 2.24,0.427 12 w/ Multi Information Display : 0.052,4.656 1.469,5.521 1.417,0.865 10 COMBINATION METER ASSEMBLY 3.448,3.583 4.042,3.99 0.594,0.406 10 CANL 3.448,3.073 3.99,3.438 0.542,0.365 10 CANH 0.49,4 1.135,4.385 0.646,0.385 10 120 Ω 4.469,3.969 5.063,4.354 0.594,0.385 10 120 Ω 3.156,3.01 3.448,3.292 0.292,0.281 10 4 3.156,3.646 3.448,3.958 0.292,0.313 10 3 3.146,3.198 3.552,3.583 0.406,0.385 10 E3 3.146,3.823 3.583,4.156 0.438,0.333 10 E3 1.333,0.604 3.208,0.99 1.875,0.385 10 : CAN Main Bus Line (CANH) 1.333,0.938 3.26,1.396 1.927,0.458 10 : CAN Main Bus Line (CANL) 1.333,1.281 3.448,1.76 2.115,0.479 10 : CAN Branch Bus Line (CANH) 1.354,1.635 3.469,2.156 2.115,0.521 10 : CAN Branch Bus Line (CANL)

C243558E03
5.063,3.229 5.49,3.583 0.427,0.354 10 +B1 5.135,3.948 5.531,4.344 0.396,0.396 10 E1 5.406,3.938 5.958,4.302 0.552,0.365 10 C24 5.49,3.042 5.76,3.344 0.271,0.302 10 7 5.448,3.75 5.875,4.063 0.427,0.313 10 32 6.188,3.219 6.99,3.927 0.802,0.708 10 to EFI MAIN Relay 5.406,3.208 5.865,3.542 0.458,0.333 10 C23 4.594,5.021 5.573,5.49 0.979,0.469 10 Trouble Area 4,2.052 4.583,2.469 0.583,0.417 10 DLC3 4.281,4.594 4.74,4.958 0.458,0.365 10 ECM 1.25,1.885 2.01,2.292 0.76,0.406 10 * : for A/T 0.115,0.115 2.479,0.542 2.365,0.427 12 w/o Multi Information Display : 3.448,3.698 4,4.031 0.552,0.333 10 CANL 3.448,3.073 4.031,3.448 0.583,0.375 10 CANH 0.49,3.969 1.104,4.365 0.615,0.396 10 120 Ω 4.469,3.969 5.042,4.344 0.573,0.375 10 120 Ω 3.156,3.01 3.51,3.302 0.354,0.292 10 4 3.156,3.635 3.563,4.031 0.406,0.396 10 3 3.146,3.208 3.563,3.583 0.417,0.375 10 E3 3.146,3.833 3.563,4.156 0.417,0.323 10 E3 1.333,0.604 3.229,1 1.896,0.396 10 : CAN Main Bus Line (CANH) 1.333,0.938 3.24,1.365 1.906,0.427 10 : CAN Main Bus Line (CANL) 1.333,1.281 3.396,1.698 2.063,0.417 10 : CAN Branch Bus Line (CANH) 1.333,1.625 3.448,2.073 2.115,0.448 10 : CAN Branch Bus Line (CANL) 0.156,4.615 0.833,5.063 0.677,0.448 10 TCM*

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>ECM Communication Stop Mode).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 5 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS LINE FOR DISCONNECTION (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C243555C07
1.896,1.135 2.385,1.427 0.49,0.292 2.417,1.729 2.177,2.323 true 1.542,2.135 2.094,2.323 true 0.094,0.083 0.521,0.448 0.427,0.365 10 *a 2.021,1.198 2.313,1.354 0.292,0.156 10 E3 2.479,1.646 3.198,1.969 0.719,0.323 10 3 (CANL) 0.885,2 1.615,2.365 0.729,0.365 10 4 (CANH)
*a Rear view of wire harness connector
(to ECM)


Disconnect the E3 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-4 (CANH) - E3-3 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
proceed to
OK
NG




OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

2.CHECK ECM POWER SOURCE CIRCUIT

b.

Check the ECM power source circuit (for K3-VE).

Click hereEngine / Hybrid System>K3-VE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit


Result:
Result proceed to
OK (for 3SZ-VE) A
OK (for K3-VE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)