Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003005 DOOR LOCK _0015188 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the any door*1 or driver side or front passenger side door*2 is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the combination meter assembly sends a key switch signal and door courtesy light switch signal.

*1: w/ Rear Door Courtesy Switch

*2: w/o Rear Door Courtesy Switch


WIRING DIAGRAM

B297226E02
3.198,6 5.292,6.646 2.094,0.646 10 BACK DOOR LOCK ASSEMBLY (Back Door Courtesy Switch) 3.208,5.833 3.729,6.135 0.521,0.302 10 L4 2.354,5 6.135,5.344 3.781,0.344 10 REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH* 2.365,4.833 2.917,5.177 0.552,0.344 10 J3 2.354,4.094 6.188,4.438 3.833,0.344 10 REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH* 2.365,3.917 2.917,4.25 0.552,0.333 10 J8 2.281,3.177 6.063,3.542 3.781,0.365 10 FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH 2.292,3.01 2.729,3.26 0.438,0.25 10 J1 2.281,2.26 6.052,2.625 3.771,0.365 10 FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH 2.292,2.083 2.698,2.354 0.406,0.271 10 J6 4.208,0.354 4.583,0.698 0.375,0.344 10 2 3.417,0.365 3.729,0.667 0.313,0.302 10 1 2.479,0.885 5.521,1.5 3.042,0.615 10 STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (Unlock Warning Switch) 2.49,0.719 3,1.01 0.51,0.292 10 E57 4.469,0.583 5.271,0.938 0.802,0.354 10 HAZARD 5.469,0.427 6.698,0.948 1.229,0.521 10 from IG1 Fuse 0.125,6.458 3.01,6.844 2.885,0.385 10 *: w/ Rear Door Courtesy Switch 0.073,6.063 2.406,6.438 2.333,0.375 10 COMBINATION METER ASSEMBLY 0.083,5.885 0.625,6.24 0.542,0.354 10 E34 1.615,0.365 2.073,0.667 0.458,0.302 10 30 1.26,0.438 1.76,0.823 0.5,0.385 10 KEY 1.625,1.729 1.99,2.031 0.365,0.302 10 1 1.438,1.844 1.823,2.156 0.385,0.313 10 L 4.854,5.417 5.281,5.813 0.427,0.396 10 3 3.406,5.417 3.708,5.708 0.302,0.292 10 4 3.406,4.5 3.75,4.792 0.344,0.292 10 1 3.406,3.594 3.74,3.979 0.333,0.385 10 1 3.406,2.656 3.802,2.979 0.396,0.323 10 1 3.406,1.729 3.74,2.104 0.333,0.375 10 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Remove the key from the key cylinder, turn the light control switch on the headlight dimmer switch assembly to the tail position, and open the driver door.

OK:

The light reminder warning buzzer sounds.


HINT:

The key reminder warning system sounds the buzzer built in to the combination meter for key reminder warnings. This buzzer is also used for the light reminder warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the lights are still on.


Result:
Proceed to
OK
NG




OK

2.INSPECT STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH)

NG

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH AND RH)
2.INSPECT STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH)
E238717C03
0.156,0.219 0.604,0.656 0.448,0.438 10 *a
*a Component without harness connected
(Steering Column Upper with Switch Bracket Assembly)


a.

Disconnect the E57 steering column upper with switch bracket assembly (unlock warning switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 No key in ignition key cylinder 10 kΩ or higher
1 - 2 Key inserted into ignition key cylinder Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - COMBINATION METER ASSEMBLY)

NG

REPLACE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - COMBINATION METER ASSEMBLY)
a.

Disconnect the E34 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E57-1 - E34-30 (KEY) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E57-1 - Body ground Always 10 kΩ or higher



c.
B297225C02
0.271,0.177 0.708,0.542 0.438,0.365 10 *a
*a Front view of wire harness connector
(to Steering Column Upper with Switch Bracket Assembly (Unlock Warning Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E57-2 - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH AND RH)
a.

Remove the front door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION

Result:
Result Proceed to
OK (w/ Rear Door Courtesy Switch) A
OK (w/o Rear Door Courtesy Switch) B
NG C




A

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH AND RH)

B

6.INSPECT BACK DOOR LOCK ASSEMBLY

C

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)

5.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH AND RH)
a.

Remove the rear door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

6.INSPECT BACK DOOR LOCK ASSEMBLY

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)

6.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION

HINT:

Inspect the back door courtesy switch only.


Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (DOOR COURTESY SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (DOOR COURTESY SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the E34 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Front Door LH
Tester Connection Condition Specified Condition
E34-1 (L) - J6-1 Always Below 1 Ω

for Front Door RH
Tester Connection Condition Specified Condition
E34-1 (L) - J1-1 Always Below 1 Ω

for Rear Door LH
Tester Connection Condition Specified Condition
E34-1 (L) - J8-1 Always Below 1 Ω

for Rear Door RH
Tester Connection Condition Specified Condition
E34-1 (L) - J3-1 Always Below 1 Ω

for Back Door
Tester Connection Condition Specified Condition
E34-1 (L) - L4-4 Always Below 1 Ω
L4-3 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E34-1 (L) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR