Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2788/41  Communication faulty (Code not coincident)  B2789/42  Communication faulty (No reply)  


DESCRIPTION

This DTC is output when: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; and 3) the ECU communication ID between the transponder key ECU assembly and the ECM are different and an engine start is attempted.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2788/41 Communication faulty (Code not coincident) When the codes are unmatched during the communication with ECM (1 trip detection logic*).
·

Transponder key ECU assembly

·

ECM

·

Wire harness


DTC Output Confirmation Operation

·

Insert the key into the ignition key cylinder.



B2789/42 Communication faulty (No reply) When no response is received during the communication with ECM (1 trip detection logic*).
·

Transponder key ECU assembly

·

ECM

·

Wire harness


DTC Output Confirmation Operation

·

Insert the key into the ignition key cylinder.




*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation When Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2788/41 -
B2789/42 -

WIRING DIAGRAM

B298746E02
4.292,2.344 7.021,2.729 2.729,0.385 10 TRANSPONDER KEY ECU ASSEMBLY 5.156,1.656 5.635,2.073 0.479,0.417 10 E 1.719,0.677 2.396,1.219 0.677,0.542 10 SIO2 5.156,0.688 5.813,1.073 0.656,0.385 10 SIO2 4.917,1.573 5.396,2.021 0.479,0.448 10 14 4.979,0.583 5.385,0.938 0.406,0.354 10 9 4.292,2.177 4.896,2.542 0.604,0.365 10 E58 2.125,0.583 2.615,1.01 0.49,0.427 10 32 1.51,2.219 2.063,2.583 0.552,0.365 10 E3 1.51,2.385 2.146,2.698 0.635,0.313 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly or ECM, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 103
OK:

DTC B2788/41 or B2789/42 is not output.


Result:
Result Proceed to
NG A
OK B




A

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the E58 transponder key ECU assembly connector.


b.

Disconnect the E3 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E58-9 (SIO2) - E3-32 (SIO2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E58-9 (SIO2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E58-14 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.REGISTER TRANSPONDER KEY ECU ASSEMBLY - ECM COMMUNICATION ID
5.REGISTER TRANSPONDER KEY ECU ASSEMBLY - ECM COMMUNICATION ID
a.

Register the transponder key ECU assembly - ECM communication ID (Refer to the Service Bulletin).

Result:
Proceed to
NEXT




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 103
OK:

DTC B2788/41 or B2789/42 is not output.


Result:
Proceed to
OK
NG




OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY