The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable sub-assembly and the steering pad.
The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1800/13 | Short in Driver Side Squib Circuit | One of the following conditions is met:
·
Short in driver side squib circuit. ·
Driver side squib malfunction. ·
Spiral cable sub-assembly malfunction. ·
Center airbag sensor assembly malfunction. |
·
Steering pad (driver side squib) ·
Spiral cable sub-assembly ·
Center airbag sensor assembly ·
Instrument panel wire |
DTC is output in check mode |
| B1801/14 | Open in Driver Side Squib Circuit | One of the following conditions is met:
·
Open in driver side squib circuit. ·
Driver side squib malfunction. ·
Spiral cable sub-assembly malfunction. ·
Center airbag sensor assembly malfunction. |
·
Steering pad (driver side squib) ·
Spiral cable sub-assembly ·
Center airbag sensor assembly ·
Instrument panel wire |
DTC is output in check mode |
| B1802/11 | Short to GND in Driver Side Squib Circuit | One of the following conditions is met:
·
Short to ground in driver side squib circuit. ·
Driver side squib malfunction. ·
Spiral cable sub-assembly malfunction. ·
Center airbag sensor assembly malfunction. |
·
Steering pad (driver side squib) ·
Spiral cable sub-assembly ·
Center airbag sensor assembly ·
Instrument panel wire |
DTC is output in check mode |
| B1803/12 | Short to B+ in Driver Side Squib Circuit | One of the following conditions is met:
·
Short to B+ in driver side squib circuit. ·
Driver side squib malfunction. ·
Spiral cable sub-assembly malfunction. ·
Center airbag sensor assembly malfunction. |
·
Steering pad (driver side squib) ·
Spiral cable sub-assembly ·
Center airbag sensor assembly ·
Instrument panel wire |
DTC is output in check mode |
When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, enter check mode (signal check) with the intelligent tester or Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Center Airbag Sensor Assembly |
| *4 | Connector E |
| *a | Front view of wire harness connector
(to Steering Pad (Driver Side Squib)) |
Disconnect the connector from the steering pad.
Connect the white wire side of SST (resistance 2.1 Ω) to connector E.
Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert the SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTCs B1800/13, B1801/14, B1802/11 or B1803/12 are not output.
Codes other than DTCs B1800/13, B1801/14, B1802/11 and B1803/12 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the SST from connector E.
Disconnect the connectors from the center airbag sensor assembly.
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Center Airbag Sensor Assembly |
Check that the connectors (on the center airbag sensor side and steering pad side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Center Airbag Sensor Assembly |
| *4 | Connector E |
| *a | Front view of wire harness connector
(to Steering Pad (Driver Side Squib)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - Body ground | Ignition switch ON | Below 1 V |
| 2 - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Tester Connection | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 1 MΩ or higher |
| 1 - Body ground | Always | 1 MΩ or higher |
| 2 - Body ground | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Steering Pad (Driver Side Squib) |
| *2 | Spiral Cable Sub-assembly |
| *3 | Center Airbag Sensor Assembly |
Connect the connectors to the steering pad and center airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTCs B1800/13, B1801/14, B1802/11 or B1803/12 are not output.
Codes other than DTCs B1800/13, B1801/14, B1802/11 and B1803/12 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the instrument panel wire connector from the spiral cable sub-assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| *A | w/o Steering Pad Switch | *B | w/ Steering Pad Switch |
| *1 | Spiral Cable Sub-assembly | *2 | Center Airbag Sensor Assembly |
| *3 | Instrument Panel Wire | *4 | Connector C |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E55-1*1, E63-1*2 (D+) - Body ground | Ignition switch ON | Below 1 V |
| E55-2*1, E63-2*2 (D-) - Body ground | Ignition switch ON | Below 1 V |
*1: w/o Steering Pad Switch
*2: w/ Steering Pad Switch
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E55-1*1, E63-1*2 (D+) - E55-2*1, E63-2*2 (D-) | Always | Below 1 Ω |
*1: w/o Steering Pad Switch
*2: w/ Steering Pad Switch
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E55-1*1, E63-1*2 (D+) - E55-2*1, E63-2*2 (D-) | Always | 1 MΩ or higher |
| E55-1*1, E63-1*2 (D+) - Body ground | Always | 1 MΩ or higher |
| E55-2*1, E63-2*2 (D-) - Body ground | Always | 1 MΩ or higher |
*1: w/o Steering Pad Switch
*2: w/ Steering Pad Switch
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG