Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.11–2013.04
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/63  Short in Front Pretensioner Squib RH Circuit  B1901/64  Open in Front Pretensioner Squib RH Circuit  B1902/61  Short to GND in Front Pretensioner Squib RH Circuit  B1903/62  Short to B+ in Front Pretensioner Squib RH Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the center airbag sensor assembly and front seat outer belt assembly RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1900/63 Short in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The center airbag sensor assembly detects a line short circuit signal in the front pretensioner squib RH circuit during the primary check.

·

A front pretensioner squib RH malfunction.

·

A center airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


DTC is output in check mode
B1901/64 Open in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The center airbag sensor assembly detects an open circuit signal in the front pretensioner squib RH circuit.

·

A front pretensioner squib RH malfunction.

·

A center airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


DTC is output in check mode
B1902/61 Short to GND in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The center airbag sensor assembly detects a short circuit to ground signal in the front pretensioner squib RH circuit.

·

A front pretensioner squib RH malfunction.

·

A center airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


DTC is output in check mode
B1903/62 Short to B+ in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The center airbag sensor assembly detects a short circuit to B+ signal in the front pretensioner squib RH circuit.

·

A front pretensioner squib RH malfunction.

·

A center airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


DTC is output in check mode

WIRING DIAGRAM

C251580E03
0.594,3.052 3.49,3.49 2.896,0.438 10 FRONT SEAT OUTER BELT ASSEMBLY RH (Front Pretensioner Squib RH) 2.146,1.417 2.417,1.604 0.271,0.188 10 D+ 2.146,2.25 2.365,2.438 0.219,0.188 10 D- 4.771,1.542 5.177,1.729 0.406,0.188 10 PDH 4.781,2.385 5.177,2.573 0.396,0.188 10 PDC 2.469,1.417 2.719,1.583 0.25,0.167 10 2 2.479,2.25 2.635,2.406 0.156,0.156 10 1 4.5,1.406 4.677,1.583 0.177,0.177 10 5 4.5,2.25 4.677,2.5 0.177,0.25 10 6 4.406,3.594 4.729,3.781 0.323,0.188 10 E66 4.406,3.781 7.073,4.042 2.667,0.26 10 CENTER AIRBAG SENSOR ASSEMBLY 0.594,2.875 0.844,3.031 0.25,0.156 10 J13

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester or Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)
a.
C251581C01
0.594,2.167 1,2.417 0.406,0.25 2.083,2.448 2.469,2.667 false 0.906,0.813 0.906,1.198 false 0.688,2.208 1,2.375 0.313,0.167 10 J13 1.021,0.917 1.198,1.094 0.177,0.177 10 D 1.24,0.917 1.417,1.094 0.177,0.177 10 C 0.646,1.698 0.906,1.875 0.26,0.177 10 *a 1.573,1.719 1.833,1.896 0.26,0.177 10 *3 2.031,1.417 2.292,1.594 0.26,0.177 10 *2 0.833,1.208 1.094,1.385 0.26,0.177 10 *1 2.531,2.635 2.865,2.792 0.333,0.156 10 SST 1.792,0.635 1.969,0.813 0.177,0.177 10 A
*1 Front Seat Outer Belt Assembly RH
(Front Pretensioner Squib RH)
*2 Center Airbag Sensor Assembly
*3 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt assembly RH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTCs B1900/63, B1901/64, B1902/61 or B1903/62 are not output.


HINT:

Codes other than DTC B1900/63, B1901/64, B1902/61 and B1903/62 may be output at this time, but they are not related to this check.


Result:
Proceed to
OK
NG




OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.
C251582C01
0.729,0.771 0.729,1.063 false 1.344,0.771 1.344,1.063 false 0.667,1.083 0.896,1.271 0.229,0.188 10 *1 1.854,0.615 2.083,0.802 0.229,0.188 10 A 0.875,0.885 1.104,1.073 0.229,0.188 10 D 1.083,0.885 1.271,1.063 0.188,0.177 10 C 1.49,0.885 1.719,1.073 0.229,0.188 10 B 1.76,1.438 1.99,1.625 0.229,0.188 10 *3 1.281,1.094 1.51,1.281 0.229,0.188 10 *2
*1 Front Seat Outer Belt Assembly RH
(Front Pretensioner Squib RH)
*2 No. 2 Floor Wire
*3 Center Airbag Sensor Assembly


Check that the connectors (on the center airbag sensor assembly side and front seat outer belt assembly RH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Result:
Proceed to
OK
NG




OK

3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
a.
C251583C01
0.75,2.167 1.167,2.417 0.417,0.25 1.646,2.354 1.188,2.844 true 1.792,2.354 2.26,2.833 true 1.406,0.781 1.406,1.146 false 0.844,0.781 0.844,1.146 false 0.833,2.208 1.115,2.375 0.281,0.167 10 J13 0.958,0.875 1.135,1.052 0.177,0.177 10 D 1.958,0.646 2.135,0.823 0.177,0.177 10 A 1.542,0.875 1.719,1.052 0.177,0.177 10 B 1.156,0.875 1.333,1.052 0.177,0.177 10 C 0.865,1.75 1.125,1.927 0.26,0.177 10 *a 1.615,1.844 1.875,2.021 0.26,0.177 10 *4 1.906,1.396 2.167,1.573 0.26,0.177 10 *3 1.354,1.208 1.615,1.385 0.26,0.177 10 *2 0.771,1.208 1.031,1.385 0.26,0.177 10 *1 0.917,2.885 1.385,3.104 0.469,0.219 10 1 (D-) 2.198,2.885 2.729,3.094 0.531,0.208 10 2 (D+)
*1 Front Seat Outer Belt Assembly RH
(Front Pretensioner Squib RH)
*2 No. 2 Floor Wire
*3 Center Airbag Sensor Assembly
*4 Connector C
*5 Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J13-1 (D-) - Body ground Ignition switch ON Below 1 V
J13-2 (D+) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-1 (D-) - J13-2 (D+) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-1 (D-) - J13-2 (D+) Always 1 MΩ or higher
J13-1 (D-) - Body ground Always 1 MΩ or higher
J13-2 (D+) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.

Result:
Proceed to
OK
NG




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C251584C01
0.865,0.823 0.865,1.167 false 0.792,1.198 1.021,1.427 0.229,0.229 10 *1 1.625,1.438 1.854,1.667 0.229,0.229 10 *2 0.969,0.917 1.167,1.094 0.198,0.177 10 C 1.104,0.917 1.302,1.094 0.198,0.177 10 D
*1 Front Seat Outer Belt Assembly RH
(Front Pretensioner Squib RH)
*2 Center Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly RH and center airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTCs B1900/63, B1901/64, B1902/61 or B1903/62 are not output.


HINT:

Codes other than DTC B1900/63, B1901/64, B1902/61 and B1903/62 may be output at this time, but they are not related to this check.


Result:
Proceed to
OK
NG




OK

NG