Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/o Rear Heated Oxygen Sensor) › 2014.04–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014987 SFI SYSTEM(w/o Rear Heated Oxygen Sensor) J

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/o Rear Heated Oxygen Sensor)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltage supplied to the +B1 (BAT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E16
1.708,0.833 2.646,1.146 0.938,0.313 10 false from EFI Fuse 1.292,1.177 2.698,1.531 1.406,0.354 10 false from EFI-MAIN Relay 0.135,1.99 2.698,2.625 2.563,0.635 10 false to Throttle Position Sensor, etc. (Sensors which have an IC) 0.135,2.646 2.552,3.385 2.417,0.74 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.948,0.729 3.365,1.052 0.417,0.323 10 false BAT 2.938,1.083 3.365,1.396 0.427,0.313 10 false +B1 3.167,2.021 3.531,2.25 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A325177E01
0.667,6.781 2.854,7.198 2.188,0.417 10 false Air Conditioning Pressure Sensor* 5,5.208 5.458,5.406 0.458,0.198 10 false VCO 5,5.771 5.458,5.969 0.458,0.198 10 false ACAD 5,6.104 5.458,6.302 0.458,0.198 10 false E24 4.698,5.219 5.156,5.417 0.458,0.198 10 false 21 4.688,5.656 5.146,5.854 0.458,0.198 10 false 26 4.688,6.115 5.146,6.313 0.458,0.198 10 false 27 2.583,3.021 2.792,3.25 0.208,0.229 10 false 3 2.229,5.323 2.688,5.521 0.458,0.198 10 false VC 2.583,3.469 2.792,3.698 0.208,0.229 10 false 2 2.042,5.771 2.563,6 0.521,0.229 10 false VOUT 2.583,3.917 2.792,4.146 0.208,0.229 10 false 1 2.313,6.229 2.521,6.458 0.208,0.229 10 false E 0.667,2.417 2.25,2.917 1.583,0.5 10 false Throttle Position Sensor 0.667,2.25 0.99,2.469 0.323,0.219 10 false C12 2.229,0.948 2.688,1.146 0.458,0.198 10 false VC 2.094,1.396 2.552,1.594 0.458,0.198 10 false PSW 2.375,1.833 2.573,2.083 0.198,0.25 10 false - 2.583,0.823 2.792,1.052 0.208,0.229 10 false 1 2.583,1.271 2.792,1.5 0.208,0.229 10 false 3 2.583,1.729 2.792,1.958 0.208,0.229 10 false 2 4.698,0.833 5.156,1.031 0.458,0.198 10 false 16 4.698,1.271 5.156,1.469 0.458,0.198 10 false 23 4.698,1.729 5.156,1.927 0.458,0.198 10 false 33 5,0.823 5.458,1.021 0.458,0.198 10 false VC 5,1.396 5.521,1.625 0.521,0.229 10 false VTHO 5,1.729 5.281,1.979 0.281,0.25 10 false E2 0.667,4.583 2.938,4.969 2.271,0.385 10 false Manifold Absolute Pressure Sensor 0.667,4.417 1.125,4.615 0.458,0.198 10 false C11 2.229,3.135 2.688,3.333 0.458,0.198 10 false VC 2.583,5.208 2.792,5.438 0.208,0.229 10 false 3 2.583,5.656 2.792,5.885 0.208,0.229 10 false 2 2.583,6.115 2.792,6.344 0.208,0.229 10 false 1 2.354,4.01 2.552,4.26 0.198,0.25 10 false - 2.177,3.573 2.635,3.771 0.458,0.198 10 false PIM 4.688,3.021 5.146,3.219 0.458,0.198 10 false 17 4.688,3.469 5.146,3.667 0.458,0.198 10 false 12 4.688,3.906 5.146,4.104 0.458,0.198 10 false 35 5,3.021 5.552,3.229 0.552,0.208 10 false VCPM 5,3.573 5.458,3.771 0.458,0.198 10 false PIM 5,3.917 5.552,4.125 0.552,0.208 10 false E2PM 5.583,6.917 6.042,7.115 0.458,0.198 10 false C24 5.583,7.094 6.042,7.292 0.458,0.198 10 false ECM 0.667,6.615 1.125,6.813 0.458,0.198 10 false B18 0.292,7.344 2.479,7.76 2.188,0.417 10 false *: w/ Cooling Fan Resister

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Light (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate (w/ Cooling Fan Resister) A
MIL does not illuminate (w/o Cooling Fan Resister) B
MIL illuminates C




A

5.CHECK MIL (AIR CONDITIONING PRESSURE SENSOR)

B

6.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)

C

5.CHECK MIL (AIR CONDITIONING PRESSURE SENSOR)
a.

Disconnect the air conditioning pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

6.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)

B

6.CHECK HARNESS AND CONNECTOR (VC CIRCUIT)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the manifold absolute pressure sensor connector.


c.

Disconnect the air conditioning pressure sensor connector*.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-16 (VC) - Body ground Always 10 kΩ or higher
C24-17 (VCPM) - Body ground Always 10 kΩ or higher
C24-21 (VCO) - Body ground* Always 10 kΩ or higher


*: w/ Cooling Fan Resister


Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C