Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(except Tropic) › from 2015.08
RM19Y0E _58 Vehicle Interior _003013 HEATING / AIR CONDITIONING _0193101 COMPRESSOR(except Tropic) A

HEATING / AIR CONDITIONING  COMPRESSOR(except Tropic)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the compressor with a new one, gradually release the refrigerant gas from the service valve and drain the following amount of oil from the new compressor before installation.

Standard:

(Oil capacity inside the new compressor: 70 to 85 cc (2.4 to 2.9 fl. oz.)) - (Remaining oil amount in the removed compressor) = (Oil amount to be removed from the new compressor)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

Since compressor oil remains in the pipes of the vehicle, if a new compressor is installed without removing some oil from the compressor, the oil amount becomes excessive. Excessive oil prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.

·

If the volume of oil remaining in the removed compressor is too small, check for oil leakage.

·

Be sure to use ND-OIL 8 for compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

a.
E321223N01
0.219,1.604 0.375,1.802 0.156,0.198 10 false 1 0.865,1.969 1.021,2.167 0.156,0.198 10 false 3 0.365,1.198 0.521,1.396 0.156,0.198 10 false 4 0.469,1.875 0.625,2.073 0.156,0.198 10 false 2

Install the cooler compressor assembly with the 4 bolts.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



b.

Connect the connector.


Hide 88712D 3.CONNECT SUCTION HOSE (for RHD)

a.

Remove the attached vinyl tape from the suction hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose.


d.

Connect the suction hose to the cooler compressor assembly with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 88712D 4.CONNECT SUCTION HOSE (for LHD)

a.

Remove the attached vinyl tape from the suction hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose.


d.

Connect the suction hose to the cooler compressor assembly with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 88711 5.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (for RHD)

a.

Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


d.

Connect the No. 1 cooler refrigerant discharge hose to the cooler compressor assembly with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 88711 6.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (for LHD)

a.

Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


d.

Connect the No. 1 cooler refrigerant discharge hose to the cooler compressor assembly with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 9. WARM UP ENGINE