Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015271 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rear Wiper Motor Circuit  


DESCRIPTION

The main body ECU (fuse block assembly) controls the rear wiper motor assembly.

WIRING DIAGRAM

E321762E01
4.667,0.979 6.052,1.323 1.385,0.344 10 false RR WIP 1.563,2.104 2.083,2.396 0.521,0.292 10 false L1 1.563,2.292 2.75,2.76 1.188,0.469 10 false Rear Wiper Motor Assembly 4.094,3.365 6.979,3.719 2.885,0.354 10 false Main Body ECU (Fuse Block Assembly) 2.688,1.333 3.208,1.625 0.521,0.292 10 false + 2.688,1.781 3.208,2.073 0.521,0.292 10 false - 2.896,1.688 3.417,1.979 0.521,0.292 10 false 1 2.906,1.25 3.427,1.542 0.521,0.292 10 false 2 3.865,1.146 4.385,1.438 0.521,0.292 10 false 9 3.823,1.583 4.344,1.875 0.521,0.292 10 false 10 3.865,2.052 4.385,2.344 0.521,0.292 10 false 1 3.844,1.354 4.365,1.646 0.521,0.292 10 false 3L 3.844,1.802 4.365,2.094 0.521,0.292 10 false 3L 3.854,2.26 4.375,2.552 0.521,0.292 10 false 3I 4.865,0.281 6.573,0.729 1.708,0.448 10 false from IG WIPER relay 6.198,1.354 6.948,1.583 0.75,0.229 10 false FWPR 6.198,1.781 6.948,2.01 0.75,0.229 10 false RWPM 6.198,2.26 6.948,2.49 0.75,0.229 10 false RWPG

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (REAR WIPER MOTOR)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS or Techstream.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Wiper Motor Rear wiper motor assembly ON or OFF -

OK:

Rear wiper motor operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT REAR WIPER MOTOR ASSEMBLY
2.INSPECT REAR WIPER MOTOR ASSEMBLY
a.

Remove the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>REMOVAL


b.

Inspect the rear wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>INSPECTION

OK:

Rear wiper motor assembly is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))

NG

REPLACE REAR WIPER MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.

Disconnect the L1 rear wiper motor assembly connector.


b.

Disconnect the 3L main body ECU (fuse block assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L1-2 (+) - 3L-9 Always Below 1 Ω
L1-1 (-) - 3L-10 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L1-2 (+) - Body ground Always 10 kΩ or higher
L1-1 (-) - Body ground Always 10 kΩ or higher
3L-9 - Body ground Always 10 kΩ or higher
3L-10 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the 3I main body ECU (fuse block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
3I-1 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR