Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015271 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Motor Circuit  


DESCRIPTION

The main body ECU (fuse block assembly) controls the washer motor assembly.

WIRING DIAGRAM

E321763E02
1.563,2.083 2.021,2.281 0.458,0.198 10 false A29 1.563,2.271 3.188,2.958 1.625,0.688 10 false Windshield Washer Motor and Pump Assembly 2.896,1.24 3.354,1.438 0.458,0.198 10 false 2 2.896,1.688 3.354,1.885 0.458,0.198 10 false 1 3.865,1.146 4.323,1.344 0.458,0.198 10 false 7 3.865,1.583 4.323,1.781 0.458,0.198 10 false 8 3.854,2.052 4.313,2.25 0.458,0.198 10 false 1 3.823,1.354 4.281,1.552 0.458,0.198 10 false 3C 3.823,1.792 4.281,1.99 0.458,0.198 10 false 3C 3.844,2.26 4.302,2.458 0.458,0.198 10 false 3I 4.094,3.365 6.917,3.667 2.823,0.302 10 false Main Body ECU (Fuse Block Assembly) 5.49,0.594 6.219,0.906 0.729,0.313 10 false WASHR 4.198,0.427 5.219,0.896 1.021,0.469 10 false from IG WIPER relay 6.208,0.427 6.938,0.74 0.729,0.313 10 false WSH 6.208,1.354 6.938,1.667 0.729,0.313 10 false RWSM2 6.208,1.802 6.938,2.115 0.729,0.313 10 false FWSM 6.198,2.271 6.927,2.583 0.729,0.313 10 false RWPG

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (FRONT WASHER MOTOR, REAR WASHER MOTOR)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS or Techstream.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front washer motor Windshield washer motor and pump assembly ON or OFF -
Rear washer motor Windshield washer motor and pump assembly ON or OFF -

OK:

Washer motor operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
2.INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
a.

Inspect the windshield washer motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>ON-VEHICLE INSPECTION

OK:

Windshield washer motor and pump assembly is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (WASHER MOTOR AND PUMP ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))

NG

REPLACE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WASHER MOTOR AND PUMP ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.

Disconnect the A29 windshield washer motor and pump assembly connector.


b.

Disconnect the 3C main body ECU (fuse block assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A29-2 - 3C-7 Always Below 1 Ω
A29-1 - 3C-8 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A29-2 - Body ground Always 10 kΩ or higher
A29-1 - Body ground Always 10 kΩ or higher
3C-7 - Body ground Always 10 kΩ or higher
3C-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the 3I main body ECU (fuse block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
3I-1 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR