While the engine is being cranked, current flows from terminal ST of the ignition or starter switch assembly to terminal STSW of the ECM (starter signal).
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Data List / STA SW.
Check the result when the ignition switch is ON and the engine starts.
| Switch Condition | STA SW |
|---|---|
| Ignition switch ON | OFF |
| Ignition switch START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Integration Relay) |
Disconnect No. 1 integration relay connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1E-6 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter relay (ST NO. 2 relay).
Click hereEngine / Hybrid System>1NR-VE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (ST NO. 2 relay circuit).
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 integration relay connector.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1J-4 - C36-1 | Always | Below 1 Ω |
| 1J-4 or C36-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-46 (STR-) - 1F-14 | Always | Below 1 Ω |
| A24-60 (STSW) - 1F-15 | Always | Below 1 Ω |
| A24-46 (STR-) or 1F-14 - Body ground | Always | 10 kΩ or higher |
| A24-60 (STSW) or 1F-15 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter relay (ST NO. 2 relay).
Click hereEngine / Hybrid System>1NR-VE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (ST NO. 2 relay circuit).
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 integration relay connector.
Disconnect the ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1F-16 - E28-4 (ST) | Always | Below 1 Ω |
| 1F-16 or E28-4 (ST) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>1NR-VE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Ignition or Starter Switch Assembly) |
Disconnect the ignition or starter switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E28-5 (AM2) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG