In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0016 | IN. DVVT System Phase Difference/Range Malfunction | Deviation in crankshaft position sensor signal and camshaft position sensor (for intake camshaft) signal
(2 trip detection logic). |
·
Valve timing ·
Camshaft timing oil control valve assembly (for intake camshaft) ·
Oil control valve filter ·
Camshaft timing gear assembly ·
ECM |
Comes on | DTC stored |
| P0017 | EX. DVVT System Phase Difference/Range Malfunction | Deviation in crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal
(2 trip detection logic). |
·
Valve timing ·
Camshaft timing oil control valve assembly (for exhaust camshaft) ·
Oil control valve filter ·
Camshaft timing exhaust gear assembly ·
ECM |
Comes on | DTC stored |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Idle the engine for 5 minutes or more [C].
Enter the following menus: Powertrain / EFI / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Drive the vehicle for 2 to 3 minutes [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 5 minutes or more [F].
Enter the following menus: Powertrain / EFI / Trouble Codes [G].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
If any DTCs other than P0016 or P0017 are output, troubleshoot those DTCs first.
| Result | Proceed to |
|---|---|
| DTC P0016 or P0017 is output | A |
| DTC P0016 or P0017 and other DTCs are output | B |
A
B
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.
Connect the GTS to the DLC3.
Start the engine.
Turn the A/C on.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 1) / All Data / DVVT actual angle, EX.DVVT actual angle.
Perform the Active Test. Check that the displacement angle varies.
Displacement angle varies.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC P0016 or P0017 is output | A |
| DTCs are not output | B |
A
B
Inspect the camshaft timing oil control valve assembly (for intake or exhaust camshaft).
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the camshaft timing gear assembly or camshaft timing exhaust gear assembly.
Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CAMSHAFT>REMOVAL
Replace the camshaft bearing cap oil hole gaskets (oil control valve filter) when removing the cylinder head cover sub-assembly.
Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the oil control valve filter.
Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY
Check that the filter is not clogged.
Filter is not clogged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC P0016 or P0017 is output | A |
| DTC is not output | B |
A
B