Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › IGNITION SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196164 IGNITION SYSTEM G

2NR-VE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1. PERFORM SPARK TEST

a.

Check for DTCs.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DTC CHECK / CLEAR: w/ Air Fuel Ratio Sensor

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/o Air Fuel Ratio Sensor)>DTC CHECK / CLEAR: w/o Air Fuel Ratio Sensor

NOTICE:

If any DTCs are present, perform troubleshooting in accordance with the procedure for each DTC.



b.

Remove the air cleaner assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>THROTTLE BODY>REMOVAL


c.

Remove the 4 ignition coil assemblies and 4 spark plugs.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL


d.
A353454

Disconnect the 4 fuel injector assembly connectors.


e.
A360044

Install a spark plug to each ignition coil assembly and connect the ignition coil assembly connector.


f.

Ground the spark plug.


g.

Check that spark occurs while the engine is being cranked.

NOTICE:
·

When performing the inspection, be sure to ground the hexagonal portion or the threaded portion of the spark plug.

·

Do not crank the engine for more than 2 seconds.

·

For vehicles with a cranking hold function, turn the ignition switch off during cranking to stop cranking.


·

If an ignition coil assembly is struck or dropped, replace it with a new one.

·

If a spark plug is struck or dropped, replace it with a new one.




h.

If spark does not occur, perform the following procedure.


Hide 2.INSPECT IGNITION COIL AND SPARK TEST

a.

Perform the spark test in accordance with the following procedure.

i.

Check that the wire harness side connector of the ignition coil assembly is securely connected.

Result:
Result Proceed to
NG Connect securely
OK Go to next step



ii.

Perform a spark test on each ignition coil assembly.

1.

If there is a cylinder where sparks do not occur, replace its ignition coil assembly with the ignition coil assembly of a cylinder where sparks occur normally.

2.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil assembly.

Result:
Result Proceed to
OK Replace ignition coil assembly
NG Go to next step




iii.

Perform a spark test on each spark plug.

1.

If there is a cylinder where sparks do not occur, replace its spark plug with the spark plug of a cylinder where sparks occur normally.

2.

Crank the engine and visually check that sparks occur at the cylinder with a known good one.

Result:
Result Proceed to
OK Replace spark plug
NG Inspect ignition system
Click here(Click here)





b.

Connect the 4 fuel injector assembly connectors.


c.

Install the 4 ignition coil assemblies and 4 spark plugs.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION



e.

Check for DTCs.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DTC CHECK / CLEAR: w/ Air Fuel Ratio Sensor

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/o Air Fuel Ratio Sensor)>DTC CHECK / CLEAR: w/o Air Fuel Ratio Sensor

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.



Hide 19100P 3.INSPECT SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not attempt to adjust the electrode gap of a used spark plug.



a.
I039522C06
0.708,1.969 1.094,1.917 false 0.563,1.875 0.74,2.042 0.177,0.167 10 *a
*a Ground


Check the electrode using a megohmmeter:

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Ground Always 10 MΩ or higher


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megohmmeter is not available, perform the following simple inspection instead.





b.
A126881

Alternative inspection method:

i.

Start the engine.

NOTICE:

Do not perform this step when any of the following DTCs are output; P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected)



ii.

Quickly accelerate the engine to 4000 rpm 5 times.

NOTICE:

Do not perform this step when any of the following DTCs are output; P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected)



iii.

Remove the spark plug.


iv.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its threads and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO SC16HR11



d.
A126880C06
0.719,1.115 0.885,1.302 0.167,0.188 10 *a
*a Electrode gap


Reference:

i.

Check the spark plug electrode gap.

Maximum Electrode Gap for a Used Spark Plug:

1.3 mm (0.0512 in.)


If the electrode gap is more than the maximum, replace the spark plug.

Electrode Gap for a New Spark Plug:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)


NOTICE:

Never attempt to adjust the electrode gap of a used spark plug.




e.
A296690

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Standard Air Pressure:

588 kPa (6 kgf/cm2, 85 psi)


Standard Duration:

20 seconds or less


HINT:

Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.