Home › Engine / Hybrid System › 2NR-VE FUEL › FUEL TANK › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042276 2NR-VE FUEL _0196207 FUEL TANK A

2NR-VE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77201 1.INSTALL FUEL TANK INLET PIPE SUB-ASSEMBLY

a.
A364923N01
0.313,1.281 0.469,1.479 0.156,0.198 10 false 1 1.458,1.521 1.615,1.719 0.156,0.198 10 false 2

Install the fuel tank inlet pipe sub-assembly with the 2 bolts in the order shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


b.

Install the fuel tank cap assembly.


Hide 77277R 2.INSTALL FUEL TANK FILLER PIPE PROTECTOR

a.

Install the fuel tank filler pipe protector with 3 new clips.


Hide 77141B 3.INSTALL NO. 1 FUEL TANK FLANGE REINFORCEMENT

a.

Install the 4 No. 1 fuel tank flange reinforcements to the fuel tank assembly.


Hide 77380 4.INSTALL FUEL CUT OFF VALVE ASSEMBLY

a.
A142203

Install the fuel cut off valve assembly onto the fuel tank assembly as shown in the illustration.


Hide 77013 5.INSTALL NO. 2 FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.
A142204C03
2.323,1.427 2.583,1.51 true 2.156,1.448 1.969,1.729 false 1.875,1.719 2.146,1.896 0.271,0.177 10 *a 2.604,1.438 2.854,1.635 0.25,0.198 10 *b
*a Groove
*b Protrusion


Align the protrusion of the fuel tank assembly with the groove of the No. 2 fuel tank breather tube sub-assembly, then install the No. 2 fuel tank breather tube sub-assembly with the 4 bolts.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


b.

Attach the No. 2 fuel tank breather tube sub-assembly to the fuel tank assembly.


Hide 77259G 6.INSTALL FUEL HOSE CLIP

a.

Engage the 4 claws to install the fuel hose clip.


Hide 77108B 7.INSTALL FUEL TANK FILLER CHECK VALVE SUB-ASSEMBLY

a.
A130592

Install the fuel tank filler check valve sub-assembly as shown in the illustration.

NOTICE:
·

Insert the fuel tank filler check valve sub-assembly until its claw fits into the spool.

·

The valve should smoothly open and close with its own weight after installing the valve.




Hide 77269A 8.INSTALL FUEL TANK BREATHER HOSE

a.
A142206C05
0.563,1.667 1,1.438 false 0.365,1.615 0.677,1.771 0.313,0.156 10 false *1 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 0.885,1.729 1.198,1.885 0.313,0.156 10 false *b 1.594,1.74 1.906,1.896 0.313,0.156 10 false *c 1.594,2.667 1.906,2.823 0.313,0.156 10 false *d 0.969,3.313 1.281,3.469 0.313,0.156 10 false *e 1.115,2.885 1.573,3.083 0.458,0.198 10 false 90°
*1 Tank Flange
*a Tank Side
*b 0 to 3 mm (0 to 0.12 in.)
*c 2 to 7 mm (0.08 to 0.28 in.)
*d Upper Side
*e LH Side


Install the fuel tank breather hose onto the fuel tank assembly with the hose clamp as shown in the illustration.


Hide 77213B 9.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A142207C06
0.656,1.104 1.281,1.104 true 1.438,0.708 1.438,0.167 1.438,0.167 1.667,0.167 false 1.948,3.146 2.26,2.927 false 1.51,4.406 1.823,4.188 false 1.344,4.344 1.656,4.5 0.313,0.156 10 false *1 2.313,2.823 2.625,2.979 0.313,0.156 10 false *2 0.469,1.031 0.781,1.188 0.313,0.156 10 false *3 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 1.719,0.083 2.031,0.24 0.313,0.156 10 false *b 1.021,1.74 1.333,1.896 0.313,0.156 10 false *c 1.708,1.76 2.021,1.917 0.313,0.156 10 false *d 1.74,2.625 2.052,2.781 0.313,0.156 10 false *e 0.865,3.531 1.177,3.688 0.313,0.156 10 false *f 1.083,2.885 1.542,3.083 0.458,0.198 10 false 90°
*1 Fuel Tank Assembly
*2 Spacer
*3 Tank Flange
*a Tank Side
*b Paint Mark
*c 0 to 3 mm (0 to 0.12 in.)
*d 2 to 10 mm (0.08 to 0.39 in.)
*e Upper Side
*f LH Side


Check that the fuel tank filler check valve sub-assembly is securely installed to the fuel tank assembly.


b.

Install the fuel tank to filler pipe hose onto the fuel tank assembly with the hose clamp as shown in the illustration.

NOTICE:
·

Install the fuel tank to filler pipe hose so the paint mark faces upward at the fuel tank side.

·

Tighten the hose clamp until it comes into contact with the spacer.




Hide 77286D 10.INSTALL NO. 2 FUEL TUBE CLAMP

a.

Engage the guide to install the No. 2 fuel tube clamp to the fuel tank assembly.


Hide 77285D 11.INSTALL NO. 1 FUEL TUBE CLAMP

a.

Engage the 2 claws to install the No. 1 fuel tube clamp to the fuel tank assembly.


Hide 23300J 12.INSTALL FUEL FILTER ASSEMBLY

a.

Install the fuel filter assembly with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 13.CONNECT FUEL PUMP HARNESS

a.

Connect the 2 fuel pump harness clamps.


Hide 77020A 14.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 87268T 15.INSTALL NO. 1 PROTECTOR

a.

Install the No. 1 protector with the 2 nuts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 77631A 16.INSTALL CENTER LOWER FUEL TANK PROTECTOR

a.

Install the center lower fuel tank protector with the 3 bolts.


Hide 77100 17.INSTALL FUEL TANK ASSEMBLY

a.

Operate the transmission jack to install the fuel tank assembly onto the vehicle.


b.
A359799N01
0.729,0.25 1,0.417 0.271,0.167 10 true 1 2.792,1.292 2.948,1.49 0.156,0.198 10 true 2 1.427,0.198 1.583,0.396 0.156,0.198 10 true 3 2.344,1.802 2.5,2 0.156,0.198 10 true 4

Tighten the 4 bolts in the sequence shown in the illustration.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


c.

Connect the fuel pump connector.


Hide 77269A 18.CONNECT FUEL TANK BREATHER HOSE

a.
A142209C03
0.771,3.458 1.115,3.677 0.344,0.219 10 150° 1.375,3.396 1.635,3.573 0.26,0.177 10 15° 1.813,2.229 2.021,2.417 0.208,0.188 10 *d 0.594,2.948 0.792,3.146 0.198,0.198 10 *e 0.094,0.073 0.281,0.229 0.188,0.156 10 *a 0.844,1.333 1.042,1.5 0.198,0.167 10 *b 1.656,1.344 1.875,1.531 0.219,0.188 10 *c
*a Inlet Pipe Side
*b 0 to 3 mm (0 to 0.12 in.)
*c 2 to 7 mm (0.08 to 0.28 in.)
*d Upper Side
*e LH Side


Connect the fuel tank breather hose to the fuel tank inlet pipe sub-assembly as shown in the illustration.


Hide 77213B 19.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A361763C01
1.167,3.552 1.844,3.552 false 0.99,3.469 1.302,3.625 0.313,0.156 10 false *1 0.177,0.104 0.49,0.26 0.313,0.156 10 false *a 1.917,1.542 2.229,1.698 0.313,0.156 10 false *b 0.99,1.542 1.302,1.698 0.313,0.156 10 false *c 1.635,2.146 1.948,2.302 0.313,0.156 10 false *d 0.802,2.969 1.115,3.125 0.313,0.156 10 false *e 2.281,3.5 2.74,3.698 0.458,0.198 10 false 60° 2.26,3.917 2.719,4.115 0.458,0.198 10 false 90°
*1 Spacer
*a Inlet Pipe Side
*b 2 to 15 mm (0.08 to 0.59 in.)
*c 0 to 3 mm (0 to 0.12 in.)
*d Upper Side
*e LH Side


Connect the fuel tank to filler pipe hose to the fuel tank inlet pipe sub-assembly as shown in the illustration.

NOTICE:

Tighten the hose clamp until it comes into contact with the spacer.



Hide 77204A 20.CONNECT FUEL TANK RETURN TUBE

a.
A359793C01
2.052,1.875 2.396,1.531 true 0.74,1.031 0.979,0.792 true 1.875,1.833 2.104,1.99 0.229,0.156 10 false *1 0.583,1 0.771,1.167 0.188,0.167 10 false *2
*1 Retainer
*2 Fuel Main Tube
V100135

Push


Insert the fuel tank return tube until it comes into contact with the fuel main tube, then push in the retainer until it makes a click sound.

NOTICE:
·

Check that there are no scratches or foreign matter around the connected parts of the fuel main tube and fuel tank return tube before this work.

·

After connecting the fuel tank return tube, check that the fuel main tube and fuel tank return tube are securely connected by pulling them.



HINT:

If connecting the tubes is too tight, apply a light coat of appropriate lubricant or gasoline to the tip of the fuel main tube.



Hide 77259C 21.CONNECT FUEL HOSE

a.
A359794C01
1.031,1.844 1.25,1.99 0.219,0.146 10 false *a 0.51,2.375 0.719,2.51 0.208,0.135 10 false *b 1.208,2.729 1.448,2.896 0.24,0.167 10 false 45° 1.677,2.917 1.906,3.073 0.229,0.156 10 false 90°
*a Upper Side
*b RH Side


Connect the fuel hose to the fuel tank to canister tube with the clip as shown in the illustration.


Hide 37110 22.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 23.ADD FUEL