Home › Engine / Hybrid System › 2NR-VE COOLING › THERMOSTAT › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042282 2NR-VE COOLING _0196239 THERMOSTAT A

2NR-VE COOLING  THERMOSTAT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL THERMOSTAT

a.
A256586C03
1.521,0.865 0.74,0.865 0.74,0.865 0.427,1.271 true 2.5,1.76 2.208,1.76 2.208,1.76 1.583,1.313 true 0.792,0.052 1.063,0.219 0.271,0.167 10 false 45° 2.083,0.063 2.427,0.229 0.344,0.167 10 false 45° 0.292,1.25 0.573,1.49 0.281,0.24 10 false *a 2.542,1.688 2.854,1.885 0.313,0.198 10 false *b
*a Mark
*b Jiggle Valve


Install the element to the water inlet as shown in the illustration.

HINT:

The jiggle valve may be set within 45° on either side of the prescribed position.



b.

Install the spring to the water inlet sub-assembly.


c.
A256584C06
1.906,0.167 2.083,0.167 2.083,0.167 2.521,0.563 true 2.51,0.844 2.792,1.646 2.792,1.646 2.792,0.573 true 1.76,0.094 2.073,0.25 0.313,0.156 10 false *1 2.74,1.688 3.052,1.844 0.313,0.156 10 false *a
*1 Frame
*a Protrusion


Install the frame to the water inlet sub-assembly.

HINT:

Using needle nose pliers, push down on the frame to compress the spring. While the spring is compressed, turn the frame to engage it to the protrusions of the water inlet sub-assembly.



Hide 16326 2.INSTALL NO. 2 WATER INLET HOUSING GASKET

a.
A256583C04
2.458,0.615 2.115,0.615 2.115,0.615 1.563,0.979 true 2.49,0.531 2.802,0.688 0.313,0.156 10 false *1
*1 No. 2 Water Inlet Housing Gasket


Install a new No. 2 water inlet housing gasket to the water inlet sub-assembly with thermostat.


Hide 16031 3.INSTALL WATER INLET SUB-ASSEMBLY WITH THERMOSTAT

a.

Install the water inlet sub-assembly with thermostat with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16572D 4.CONNECT NO. 2 RADIATOR HOSE

a.
A360193C01
2.458,0.896 2.667,0.667 2.667,0.667 2.802,0.667 true 2.844,0.583 3.156,0.74 0.313,0.156 10 false *a 2.354,0.417 2.667,0.573 0.313,0.156 10 false *b
*a Paint Mark
*b Upper Side


Connect the No. 2 radiator hose to the water inlet sub-assembly with thermostat with the clip as shown in the illustration.


Hide 16281 5.CONNECT NO. 4 WATER BY-PASS HOSE

a.
A364884C01
1.667,0.875 1.813,0.771 true 1.854,0.635 2.167,0.792 0.313,0.156 10 false *a 1.542,0.427 1.854,0.583 0.313,0.156 10 false *b 0.375,0.708 0.688,0.865 0.313,0.156 10 false *c
*a Paint Mark
*b Upper Side
*c 2.0 to 6.0 mm (0.0787 to 0.2362 in.)


Connect the No. 4 water by-pass hose with the clip as shown in the illustration.


Hide 8.INSPECT FOR COOLANT LEAK

Hide 51441 9.INSTALL NO. 1 ENGINE UNDER COVER