Home › Engine / Hybrid System › 2NR-VE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042274 2NR-VE ENGINE MECHANICAL _0196193 ENGINE ASSEMBLY A

2NR-VE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.REMOVE ENGINE STAND

a.

Using a sling device and chain block, remove the engine assembly from the engine stand.

NOTICE:
·

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.




b.

Set the engine assembly to the engine lifter.

NOTICE:
·

Set the engine assembly so that it is horizontal.

·

Do not tighten the rope or belt with a tightening mechanism more than necessary.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 31250 4.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 31210 5.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31210 6.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 12315 7.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A363038N01
2.271,0.688 2.615,0.917 0.344,0.229 10 true 4 (A) 1.896,0.646 2.135,0.854 0.24,0.208 10 true 1 1.781,0.969 2.021,1.177 0.24,0.208 10 true 2 2.531,1 2.771,1.208 0.24,0.208 10 true 3

Temporarily tighten the front No. 1 engine mounting bracket LH with the bolt (A).


b.

Temporarily tighten the 3 bolts.


c.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 12311 8.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.
A363037N01
1.646,1.271 2.01,1.552 0.365,0.281 10 true 3 (A) 0.438,0.99 0.615,1.229 0.177,0.24 10 true 1 1.583,0.292 1.76,0.531 0.177,0.24 10 true 2

Temporarily tighten the front No. 1 engine mounting bracket RH with the bolt (A).


b.

Temporarily tighten the 2 bolts.


c.

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 12361 9.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the 2 front engine mounting insulators with the 2 new nuts.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 51201 10.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Operate the engine sling device and chain block, then temporarily install the front suspension crossmember sub-assembly with the 4 new bolts.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.



b.

Fully tighten the 4 bolts.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 11.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 12.INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)

Hide 13.REMOVE ENGINE HANGER

a.

for Manual Transmission:

i.

Using a sling device and chain block, set the engine assembly with transmission on the engine lifter.

NOTICE:
·

Place the height adjustments or plate lift attachments so that the engine assembly with transmission is level.

·

Securely support the engine assembly with transmission to prevent it from turning upside down until it is secured to the engine lifter.

·

To prevent deformation of the oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the engine assembly.





b.

for Automatic Transmission:

i.

Using a sling device and chain block, set the engine assembly with transmission on the engine lifter.

NOTICE:
·

Place the height adjustments or plate lift attachments so that the engine assembly with transmission is level.

·

Securely support the engine assembly with transmission to prevent it from turning upside down until it is secured to the engine lifter.

·

To prevent deformation of the oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the engine assembly.

·

To prevent deformation of the transmission oil pan sub-assembly, never set any attachments against the transmission oil pan sub-assembly.





c.

Remove the 2 bolts and 2 engine hangers.


Hide 28100 14.INSTALL STARTER ASSEMBLY (for Automatic Transmission)

Hide 28100 15.INSTALL STARTER ASSEMBLY (for Manual Transmission)

Hide 25051 16.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 16507 17.INSTALL RADIATOR PIPE SUB-ASSEMBLY

Hide 87246X 18.CONNECT NO. 2 HEATER WATER HOSE (w/ Heater)

a.
A364917C01
2.229,0.25 2.542,0.406 0.313,0.156 10 false *a 3.052,1.063 3.365,1.219 0.313,0.156 10 false *b 2.75,0.583 3.063,0.74 0.313,0.156 10 false *c
*a Upper Side
*b LH Side
*c 90°


Connect the No. 2 heater water hose with the clip as shown in the illustration.

HINT:

Install the clip so that it is positioned as shown in the illustration.



Hide 87245X 19.CONNECT HEATER WATER HOSE (w/ Heater)

a.
A364918C01
2.188,0.052 2.5,0.208 0.313,0.156 10 false *a 2.958,0.885 3.271,1.042 0.313,0.156 10 false *b 2.688,0.427 3,0.583 0.313,0.156 10 false *c
*a Upper Side
*b LH Side
*c 90°


Connect the heater water hose with the clip as shown in the illustration.

HINT:

Install the clip so that it is positioned as shown in the illustration.



Hide 16283 20.INSTALL NO. 6 WATER BY-PASS HOSE (w/o Heater)

a.

Install the No. 6 water by-pass hose with the 2 clips


Hide 16591A 21.CONNECT RADIATOR PIPE RADIATOR HOSE

Hide 23.CONNECT ENGINE WIRE

a.

Connect all of the clamps and connectors of the engine wire to the engine assembly.


b.

Connect the engine wire with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 25.INSTALL ENGINE AND TRANSMISSION ASSEMBLY

a.

Operate the engine lifter and lift the engine assembly with transmission.

NOTICE:

While raising the engine assembly with transmission, do not allow it to contact the vehicle body.



b.

Install the engine assembly with transmission with the 4 bolts to the vehicle.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


c.

Install the rear engine support member sub-assembly with the 6 bolts.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


d.
C245923

Install the front lower suspension crossmember sub-assembly with 4 new bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.
C245924

Install the front lower suspension crossmember sub-assembly with 2 new bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


f.
A366996

Tighten the rear engine mounting insulator bolt.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 45047 26.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 27.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 28.CONNECT FRONT LOWER SUSPENSION ARM

a.

Install the front lower suspension arm onto the steering knuckle with a new castle nut.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)

NOTICE:

Make sure that grease does not adhere to the threads or the tapered part.



b.

Install a new clip.


Hide 29.INSTALL FRONT STABILIZER BRACKET

Hide 48810 30.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Install the front stabilizer link assembly with a new nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a socket hexagon wrench 6 mm to hold the stud.



Hide 48820B 31.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 32922A 32.INSTALL OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 32921D 33.INSTALL OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 16572D 34.INSTALL NO. 2 RADIATOR HOSE

a.
A361373C01
0.698,1.115 1.01,1.271 0.313,0.156 10 false *a 0,0.156 0.313,0.313 0.313,0.156 10 false *b 2.823,0.063 3.135,0.219 0.313,0.156 10 false *a 0.875,1.813 1.188,1.969 0.313,0.156 10 false *b 3.052,0.208 3.365,0.365 0.313,0.156 10 false *b
*a Upper Side
*b 90°


Install the No. 2 radiator hose with the 2 hose clamps as shown in the illustration.

HINT:

Install the hose clamps so that they are positioned as shown in the illustration.



Hide 23901 35.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel tank to canister tube sub-assembly until a "click" sound is heard.

NOTICE:
·

Make sure to read the disconnecting the fuel tube connector notice before proceeding with work.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION

·

After connecting the fuel lines, check that the fuel tube connector and fuel tank to canister tube sub-assembly are securely connected by pulling on them.




Hide 23841B 36.INSTALL EFI FUEL PIPE CLAMP

a.

Install the EFI fuel pipe clamp.


Hide 17410 38.SET FRONT EXHAUST PIPE ASSEMBLY

Hide 58151A 39.INSTALL NO. 1 FLOOR HEAT INSULATOR

Hide 17410 40.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 89465A 41.INSTALL NO. 2 OXYGEN SENSOR (w/ Air Fuel Ratio Sensor)

Hide 31470 42.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)

a.

Install the clutch release cylinder assembly with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33820B 43.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 33820B 44.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transmission)

Hide 37110 45.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 45220 46.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.

Install a new bolt on the steering intermediate shaft assembly.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 47.DISCONNECT ENGINE WIRE

a.

Engage the 2 harness clamps.


b.

Connect the 4 connectors of the engine wire to the engine room relay block and engage the 2 claws.


c.

Connect the ECM connector and lock the lever.


d.

Connect the engine wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 87246X 48.CONNECT NO. 2 HEATER WATER HOSE (w/ Heater)

Hide 87245X 49.CONNECT HEATER WATER HOSE (w/ Heater)

Hide 82661 50.INSTALL NO. 1 RELAY BLOCK COVER

Hide 88320 51.INSTALL COOLER COMPRESSOR ASSEMBLY

a.
A360095N01
2.188,0.844 2.635,1.063 0.448,0.219 10 true 4 (A) 1.896,1.75 2.073,1.958 0.177,0.208 10 true 1 2.49,1.813 2.667,2.021 0.177,0.208 10 true 2 1.115,0.531 1.292,0.74 0.177,0.208 10 true 3

Temporarily tighten the cooler compressor assembly with the bolt A.


b.

Temporarily tighten the 3 bolts.


c.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)


d.

Connect the connector.


Hide 44730A 52.CONNECT NO. 1 VACUUM HOSE (for RHD)

Hide 44730A 53.INSTALL NO. 1 VACUUM HOSE (for LHD)

a.
A364919C01
1.198,0.146 1.51,0.302 0.313,0.156 10 false *a 3.063,3.625 3.375,3.781 0.313,0.156 10 false *b 1.771,0.49 2.083,0.646 0.313,0.156 10 false *c 2.792,4.042 3.104,4.198 0.313,0.156 10 false *d 2.208,3.042 2.521,3.198 0.313,0.156 10 false *a 2.063,0.844 2.375,1 0.313,0.156 10 false *b
*a Upper Side
*b Front Side
*c 180°
*d 90°


Install the No. 1 vacuum hose with the 2 clips as shown in the illustration.

HINT:

Install the clips so that they are positioned as shown in the illustration.



Hide 17881 54.INSTALL NO. 1 AIR CLEANER HOSE

Hide 55.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 2 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


Hide 17801 56.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly.


Hide 17705 57.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

A361374C01
1.667,1.167 1.771,0.927 false 1.51,1.135 1.823,1.292 0.313,0.156 10 false *1
*1 Stopper


a.

Lock the 2 clamps and install the air cleaner cap sub-assembly.


b.

Connect the No. 1 air cleaner hose with the clamp.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)

NOTICE:

Install the hose clamp so that the clamp makes contact with the stopper.



c.

Engage the guide and connect the No. 2 ventilation hose.


d.

Connect the harness clamp and connector to the intake air flow meter assembly.


e.

Connect the harness clamp to the air cleaner cap sub-assembly.


Hide 77754 58.CONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE

a.

for LHD:

i.

Engage the 2 guides and connect the No. 1 charcoal canister outlet hose to the air cleaner cap sub-assembly.



b.

for RHD:

i.

Connect the No. 1 charcoal canister outlet hose to the charcoal canister outlet guide.


ii.

Engage the clamp.



Hide 25860 59.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

Hide 16571C 60.INSTALL NO. 1 RADIATOR HOSE

Hide 16361A 61.INSTALL FAN AND GENERATOR V BELT

Hide 17775A 62.INSTALL NO. 3 AIR CLEANER PIPE BRACKET

a.

Install the No. 3 air cleaner pipe bracket with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17750A 63.INSTALL AIR CLEANER INLET ASSEMBLY

a.

Install the air cleaner inlet assembly with the 2 bolts

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.
A363055C01
1.906,1.865 2.135,1.625 false 1.781,1.885 2.094,2.083 0.313,0.198 10 false *a
*1 Stopper


Connect the air cleaner inlet assembly to the air cleaner cap sub-assembly with the clamp.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)

NOTICE:

Install the clamp so that the clamp makes contact with the stopper.



c.

Connect the earth cable with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 74411 64.INSTALL BATTERY CARRIER

a.

Install the battery carrier with the 4 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 65.INSTALL BATTERY

a.

Install the battery.


b.

Install the battery cover.


c.

Install the battery hold down clamp sub-assembly with the bolt and nut.

Torque:
Bolt : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Nut : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Tighten the nut and connect the positive (+) battery terminal.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 66.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 67.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 68.INSPECT MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 72.INSPECT FOR ENGINE COOLANT LEAK

Hide 75.INSPECT MANUAL TRANSMISSION OIL LEAK (for Manual Transmission)

Hide 76.INSPECT FOR FLUID LEAK (for Automatic Transmission)

Hide 77.INSPECT AUTOMATIC TRANSMISSION FLUID LEVEL (for Automatic Transmission)

Hide 78.INSPECT SHIFT LEVER POSITION (for Automatic Transmission)

Hide 79.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 81.FULLY TIGHTEN FRONT LOWER SUSPENSION ARM

Hide 51441 85.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 8 bolts and the clip.


Hide 51443 86.INSTALL NO. 2 ENGINE UNDER COVER (w/ No. 2 Engine Under Cover)

a.

Install the No. 2 engine under cover with the 8 bolts.


Hide 87.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT