Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003012 SEAT BELT _0015223 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

When the ignition switch is turned to ON, the main body ECU (fuse block assembly) determines whether the front seat inner belt assembly RH*1 or LH*2 is fastened or not, and transmits a signal to the combination meter assembly through the CAN. If the front seat inner belt assembly RH*1 or LH*2 is unfastened, the combination meter assembly will cause the driver side seat belt warning light to blink.When the front seat inner belt assembly RH*1 or LH*2 is fastened, the warning light goes off.

*1: for RHD

*2: for LHD


WIRING DIAGRAM

E324024E01
0.656,2.333 4.323,2.531 3.667,0.198 10 false : CAN Communication Line 0.167,1.594 1.365,2 1.198,0.406 10 false Combination Meter Assembly 5.24,1.167 6.594,1.885 1.354,0.719 10 false Front Seat Inner Belt Assembly RH*1/LH*2 2.146,1.5 4.667,1.833 2.521,0.333 10 false Main Body ECU (Fuse Block Assembly) 3.438,0.708 3.938,0.917 0.5,0.208 10 false DBKL 2.833,0.417 3.333,0.625 0.5,0.208 10 false CANH 0.802,0.417 1.302,0.625 0.5,0.208 10 false CANH 6.146,0.594 6.49,0.844 0.344,0.25 10 false 2 2.063,0.188 2.406,0.438 0.344,0.25 10 false 17 5.24,1 7.135,2.125 1.896,1.125 10 false J23*1 5.323,0.604 5.667,0.854 0.344,0.25 10 false 1 4.396,0.708 4.74,0.958 0.344,0.25 10 false 3K 5.49,0.698 5.833,0.948 0.344,0.25 10 false + 5.979,0.688 6.323,0.938 0.344,0.25 10 false - 0.833,1.031 1.333,1.24 0.5,0.208 10 false CANL 2.833,1.031 3.333,1.24 0.5,0.208 10 false CANL 2.052,1.021 2.552,1.229 0.5,0.208 10 false 3G 2.052,0.417 2.552,0.625 0.5,0.208 10 false 3G 2.073,0.792 2.417,1.042 0.344,0.25 10 false 16 1.323,0.833 1.667,1.083 0.344,0.25 10 false 8 4.406,0.5 4.75,0.75 0.344,0.25 10 false 10 1.323,0.25 1.667,0.5 0.344,0.25 10 false 9 0.167,1.458 0.667,1.667 0.5,0.208 10 false E34 5.74,1 7.156,2.313 1.417,1.313 10 false J24*2 2.552,2.333 4.083,2.531 1.531,0.198 10 false *1 for RHD 3.417,2.333 4.948,2.531 1.531,0.198 10 false *2 for LHD

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (DRIVER BUCKLE SW)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical / Body / Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver buckle SW Driver side seat belt buckle switch ON or OFF ON: Driver side seat belt unfastened
OFF: Driver side seat belt fastened
-

OK:

The GTS or Techstream display changes correctly in response to the driver side seat belt condition.


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY
2.INSPECT FRONT SEAT INNER BELT ASSEMBLY
a.

Remove the front seat inner belt assembly RH*1 or LH*2.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly RH*1 or LH*2.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION

*1: for RHD

*2: for LHD



Result:
Result Proceed to
OK A
NG (for RHD) B
NG (for LHD) C



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - FRONT SEAT INNER BELT ASSEMBLY - BODY GROUND)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - FRONT SEAT INNER BELT ASSEMBLY - BODY GROUND)
a.

Disconnect the 3K main body ECU (fuse block assembly) connector.


b.

Disconnect the J23*1 or J24*2 front seat inner belt assembly RH*1 or LH*2 connector.


*1: for RHD

*2: for LHD


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
3K-10 - J23-1 (+) Always Below 1 Ω
J23-2 (-) - Body ground Always Below 1 Ω
3K-10 or J23-1 (+) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
3K-10 - J24-1 (+) Always Below 1 Ω
J24-2 (-) - Body ground Always Below 1 Ω
3K-10 or J24-1 (+) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG C




A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR