Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/73  Short in Front Pretensioner Squib RH Circuit  B1901/73  Open in Front Pretensioner Squib RH Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the airbag ECU assembly and front seat outer belt assembly RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1900/73 Short in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal in the front pretensioner squib RH circuit during the primary check

·

A front pretensioner squib RH malfunction

·

A airbag ECU assembly malfunction


·

Instrument panel wire

·

Floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Airbag ECU assembly


DTC is output in check mode
B1901/73 Open in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The airbag ECU assembly detects an open circuit signal in the front pretensioner squib RH circuit

·

A front pretensioner squib RH malfunction

·

A airbag ECU assembly malfunction


·

Instrument panel wire

·

Floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Airbag ECU assembly


DTC is output in check mode

WIRING DIAGRAM

C251577E08
2.104,0.833 2.417,1.031 0.313,0.198 10 false 2 2.104,1.865 2.417,2.063 0.313,0.198 10 false 1 5.104,0.854 5.417,1.052 0.313,0.198 10 false 3 5.094,1.875 5.406,2.073 0.313,0.198 10 false 4 5.354,0.969 5.771,1.198 0.417,0.229 10 false PR+ 5.365,2.01 5.781,2.24 0.417,0.229 10 false PR- 0.979,2.781 1.292,2.979 0.313,0.198 10 false J13 5.25,2.771 5.563,2.969 0.313,0.198 10 false J18 0.979,2.938 3.167,3.552 2.188,0.615 10 false Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 5.25,2.938 6.917,3.365 1.667,0.427 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS or Techstream.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM



PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)
a.
C312973C03
0.417,2.25 0.833,2.5 0.417,0.25 0.656,0.813 0.656,1.146 false 2.396,2.385 2.073,2.385 false 0.604,1.198 0.917,1.354 0.313,0.156 10 false *1 2.302,1.417 2.615,1.573 0.313,0.156 10 false *2 1.583,1.75 1.896,1.906 0.313,0.156 10 false *3 0.448,1.865 0.76,2.021 0.313,0.156 10 false *a 0.771,0.958 1.083,1.115 0.313,0.156 10 false D 1,0.958 1.313,1.115 0.313,0.156 10 false C 2.042,0.688 2.354,0.844 0.313,0.156 10 false A 2.458,2.302 2.865,2.615 0.406,0.313 10 false SST 0.521,2.292 0.927,2.604 0.406,0.313 10 false J13
*1 Front Seat Outer Belt Assembly RH
(Front Pretensioner Squib RH)
*2 Airbag ECU Assembly
*3 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat outer belt assembly RH (front pretensioner squib RH).


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector D.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Body Electrical > A/B > Clear DTCs
50002 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Body Electrical > A/B > Trouble Codes
50001 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1900/73 or B1901/73 is not output.


HINT:

Codes other than DTC B1900/73 and B1901/73 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connector from the airbag ECU assembly.


e.
C312974C01
0.365,0.792 0.365,1.031 false 1.125,0.792 1.125,1.031 false 0.292,1.073 0.604,1.229 0.313,0.156 10 false *1 1.073,1.073 1.385,1.229 0.313,0.156 10 false *2 2.167,1.448 2.479,1.604 0.313,0.156 10 false *3 0.479,0.917 0.792,1.073 0.313,0.156 10 false D 0.719,0.917 1.031,1.073 0.313,0.156 10 false C 1.469,0.917 1.781,1.073 0.313,0.156 10 false B 1.906,0.625 2.219,0.781 0.313,0.156 10 false A
*1 Front Seat Outer Belt Assembly RH
(Front Pretensioner Squib RH)
*2 Floor Wire
*3 Airbag ECU Assembly


Check that the connectors (on the airbag ECU assembly side and front seat outer belt assembly RH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT PRETENSIONER SQUIB RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT PRETENSIONER SQUIB RH CIRCUIT
a.
C312975C03
0.51,2.25 0.927,2.5 0.417,0.25 0.229,0.781 0.229,1.073 false 1.104,0.792 1.104,1.083 false 1.656,2.354 1.375,2.615 1.375,2.615 1.208,2.615 true 1.792,2.354 2.115,2.615 2.115,2.615 2.292,2.615 true 0.146,1.125 0.458,1.281 0.313,0.156 10 false *1 1.063,1.125 1.375,1.281 0.313,0.156 10 false *2 2.24,1.406 2.552,1.563 0.313,0.156 10 false *3 1.646,1.865 1.958,2.021 0.313,0.156 10 false *4 0.615,1.729 0.927,1.885 0.313,0.156 10 false *a 0.344,0.927 0.656,1.083 0.313,0.156 10 false D 0.688,0.927 1,1.083 0.313,0.156 10 false C 1.448,0.927 1.76,1.083 0.313,0.156 10 false B 1.979,0.635 2.292,0.792 0.313,0.156 10 false A 1.063,2.531 1.313,2.75 0.25,0.219 10 false 1 2.354,2.531 2.625,2.76 0.271,0.229 10 false 2 0.625,2.292 1.115,2.563 0.49,0.271 10 false J13
*1 Front Seat Outer Belt Assembly RH
(Front Pretensioner Squib RH)
*2 Floor Wire
*3 Airbag ECU Assembly
*4 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J13-1 - Body ground Ignition switch ON Below 1 V
J13-2 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-1 - J13-2 Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-1 - J13-2 Always 1 MΩ or higher
J13-1 - Body ground Always 1 MΩ or higher
J13-2 - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG ECU ASSEMBLY

NG

REPLACE FLOOR WIRE

4.CHECK AIRBAG ECU ASSEMBLY
a.
C312976C01
0.677,0.823 0.677,1.073 false 0.615,1.104 0.927,1.26 0.313,0.156 10 false *1 2.115,1.438 2.427,1.594 0.313,0.156 10 false *2 0.792,0.948 1.104,1.104 0.313,0.156 10 false C 1.833,0.677 2.146,0.833 0.313,0.156 10 false A
*1 Front Seat Outer Belt Assembly RH
(Front Pretensioner Squib RH)
*2 Airbag ECU Assembly


Connect the connectors to the front seat outer belt assembly RH (front pretensioner squib RH) and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Body Electrical > A/B > Clear DTCs
50002 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > A/B > Trouble Codes
50001 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1900/73 or B1901/73 is not output.


HINT:

Codes other than DTC B1900/73 and B1901/73 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG