The front pretensioner squib LH circuit consists of the airbag ECU assembly and front seat outer belt assembly LH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1905/74 | Short in Front Pretensioner Squib LH Circuit | One of the following conditions is met:
·
The airbag ECU assembly detects a line short circuit signal in the front pretensioner squib LH circuit during the primary check ·
A front pretensioner squib LH malfunction ·
A airbag ECU assembly malfunction |
·
Instrument panel wire ·
Floor wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Airbag ECU assembly |
DTC is output in check mode |
| B1906/74 | Open in Front Pretensioner Squib LH Circuit | One of the following conditions is met:
·
The airbag ECU assembly detects an open circuit signal in the front pretensioner squib LH circuit ·
A front pretensioner squib LH malfunction ·
A airbag ECU assembly malfunction |
·
Instrument panel wire ·
Floor wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Airbag ECU assembly |
DTC is output in check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag ECU assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Perform the simulation method by selecting check mode (Signal Check) using the GTS or Techstream.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
After selecting check mode (Signal Check), perform simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
| *1 | Front Seat Outer Belt Assembly LH
(Front Pretensioner Squib LH) |
| *2 | Airbag ECU Assembly |
| *3 | Connector C |
| *a | Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH)) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front seat outer belt assembly LH (front pretensioner squib LH).
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E.
Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1905/74 or B1906/74 is not output.
Codes other than DTC B1905/74 and B1906/74 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the connector from the airbag ECU assembly.
| *1 | Front Seat Outer Belt Assembly LH
(Front Pretensioner Squib LH) |
| *2 | Floor Wire |
| *3 | Airbag ECU Assembly |
Check that the connectors on the airbag ECU assembly side and front seat outer belt assembly LH side are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Seat Outer Belt Assembly LH
(Front Pretensioner Squib LH) |
| *2 | Floor Wire |
| *3 | Airbag ECU Assembly |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH)) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J14-1 - Body ground | Ignition switch ON | Below 1 V |
| J14-2 - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J14-1 - J14-2 | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J14-1 - J14-2 | Always | 1 MΩ or higher |
| J14-1 - Body ground | Always | 1 MΩ or higher |
| J14-2 - Body ground | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Seat Outer Belt Assembly LH
(Front Pretensioner Squib LH) |
| *2 | Airbag ECU Assembly |
Connect the connectors to the front seat outer belt assembly LH (front pretensioner squib LH) and airbag ECU assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1905/74 or B1906/74 is not output.
Codes other than DTC B1905/74 and B1906/74 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG