Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003005 DOOR LOCK _0015188 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the combination meter assembly sends a key switch signal and door courtesy light switch signal.

WIRING DIAGRAM

B417934E01
4.438,3.896 7.083,4.333 2.646,0.438 10 false Main Body ECU (Fuse Block Assembly) 0.563,4.354 2.656,4.74 2.094,0.385 10 false : CAN Communication Line 0.719,3.844 3.01,4.24 2.292,0.396 10 false Combination Meter Assembly 0.729,3.667 1.271,4.042 0.542,0.375 10 false E34 0.552,2.552 3.99,3.052 3.438,0.5 10 false Courtesy Light Switch (for Front LH*1/RH*2 Side) 0.823,1.438 3.5,2.198 2.677,0.76 10 false Steering Column Upper with Switch Bracket Assembly (Unlock Warning Switch) 0.833,1.26 1.375,1.635 0.542,0.375 10 false E57 4.281,0.865 4.927,1.198 0.646,0.333 10 false HORN 2.5,0.281 3.656,0.677 1.156,0.396 10 false from Battery 2.469,4.448 3.563,4.813 1.094,0.365 10 false *1: for LHD 3.375,4.448 4.469,4.813 1.094,0.365 10 false *2: for RHD 1.75,3.063 2.406,3.406 0.656,0.344 10 false CANH 6.073,3.073 6.729,3.417 0.656,0.344 10 false CANH 1.771,3.479 2.427,3.823 0.656,0.344 10 false CANL 6.083,3.479 6.74,3.823 0.656,0.344 10 false CANL 3.802,3.479 4.344,3.854 0.542,0.375 10 false 3G 3.802,3.063 4.344,3.438 0.542,0.375 10 false 3G 3.813,2.219 4.354,2.594 0.542,0.375 10 false 3L 3.792,1.146 4.333,1.521 0.542,0.375 10 false 3G 3.813,2.865 4.354,3.24 0.542,0.375 10 false 17 3.802,3.271 4.344,3.646 0.542,0.375 10 false 16 2.271,3.323 2.813,3.698 0.542,0.375 10 false 8 2.271,2.896 2.813,3.271 0.542,0.375 10 false 9 2.583,2.104 3.125,2.479 0.542,0.375 10 false 1 0.573,2.198 1.198,2.49 0.625,0.292 10 false J20*1 3.802,0.948 4.344,1.323 0.542,0.375 10 false 15 2.281,1.135 2.823,1.51 0.542,0.375 10 false - 2.25,0.698 2.792,1.073 0.542,0.375 10 false + 2.5,0.594 3.042,0.969 0.542,0.375 10 false 2 2.49,1.031 3.031,1.406 0.542,0.375 10 false 1 6.073,2.219 6.729,2.563 0.656,0.344 10 false IDCTY 6.083,1.146 6.74,1.49 0.656,0.344 10 false KSW 3.802,2.01 4.344,2.385 0.542,0.375 10 false 13 0.573,2.375 1.198,2.667 0.625,0.292 10 false J19*2 3.823,0.719 4.365,1.094 0.542,0.375 10 false 3I 3.792,0.292 4.333,0.667 0.542,0.375 10 false 3A 3.833,0.094 4.375,0.469 0.542,0.375 10 false 1 3.854,0.521 4.396,0.896 0.542,0.375 10 false 9

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Remove the key from the key cylinder, turn the light control switch on the headlight dimmer switch assembly to the tail position, and open the driver door.

OK:

The light reminder warning buzzer sounds.


HINT:

The key reminder warning system sounds the buzzer built in to the combination meter for key reminder warnings. This buzzer is also used for the light reminder warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the lights are still on.


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING GTS OR TECHSTREAM (DRIVER DOOR COURTESY SW)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS OR TECHSTREAM (DRIVER DOOR COURTESY SW)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical > Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver door courtesy SW Driver side door courtesy light switch signal OFF or ON OFF: Driver side door closed
ON: Driver side door open
-

OK:

On the GTS or Techstream screen, the display changes between ON and OFF as shown in the table above.


Result:
Proceed to
OK
NG




OK

3.READ VALUE USING GTS OR TECHSTREAM (KEY SW)

NG

4.INSPECT COURTESY LIGHT SWITCH
3.READ VALUE USING GTS OR TECHSTREAM (KEY SW)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical > Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
KEY SW Key switch signal OFF or ON OFF: No key in ignition key cylinder
ON: Key inserted in ignition key cylinder
-

OK:

On the GTS or Techstream screen, the display changes between ON and OFF as shown in the table above.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

6.INSPECT STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH)
4.INSPECT COURTESY LIGHT SWITCH
a.

Remove the courtesy light switch.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the courtesy light switch.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COURTESY LIGHT SWITCH - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))

NG

5.CHECK HARNESS AND CONNECTOR (COURTESY LIGHT SWITCH - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.

Disconnect the 3L main body ECU (fuse block assembly) connector.


b.

Disconnect the J20*1 or J19*2 courtesy light switch connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
3L-13 - J20-1 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
3L-13 - J19-1 Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
3L-13 or J20-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
3L-13 or J19-1 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH)
E238717C05
1.25,1.865 1.417,1.865 1.417,1.865 1.583,1.365 true 2.177,1.865 2.01,1.865 2.01,1.865 1.844,1.365 true 0.198,0.135 0.573,0.531 0.375,0.396 10 false *a 1.094,1.781 1.552,2.083 0.458,0.302 10 false + 2.271,1.771 2.646,2.104 0.375,0.333 10 false -
*a Component without harness connected
(Steering Column Upper with Switch Bracket Assembly (Unlock Warning Switch))


a.

Disconnect the E57 steering column upper with switch bracket assembly (unlock warning switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (-) - 2 (+) No key in ignition key cylinder 10 kΩ or higher
1 (-) - 2 (+) Key inserted into ignition key cylinder Below 1 Ω


Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (BATTERY, STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH) - MAIN BODY ECU (FUSE BLOCK ASSEMBL))

NG

REPLACE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BATTERY, STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (UNLOCK WARNING SWITCH) - MAIN BODY ECU (FUSE BLOCK ASSEMBL))
a.

Disconnect the 3G main body ECU (fuse block assembly) connector.


b.

Disconnect the E57 steering column upper with switch bracket assembly (unlock warning switch) connector.


c.
B297225C04
1.51,0.25 1.927,0.5 0.417,0.25 1.896,1.5 2.125,1.948 2.125,1.948 2.26,1.948 true 0.208,0.167 0.615,0.552 0.406,0.385 10 false *a 1.594,0.302 2.177,0.635 0.583,0.333 10 false E57 2.333,1.875 2.688,2.177 0.354,0.302 10 false +
*a Front view of wire harness connector
(to Steering Column Upper with Switch Bracket Assembly (Unlock Warning Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E57-2 (+) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E57-1 (-) - 3G-15 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E57-1 (-) or 3G-15 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR