Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0016  IN. DVVT System Phase Difference/Range Malfunction  P0017  EX. DVVT System Phase Difference/Range Malfunction  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 IN. DVVT System Phase Difference/Range Malfunction Deviation in crankshaft position sensor signal and camshaft position sensor (for intake camshaft) signal
(2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored
P0017 EX. DVVT System Phase Difference/Range Malfunction Deviation in crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal
(2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for exhaust camshaft)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A197314E52
4.24,1.115 4.604,0.448 4.604,0.448 4.75,0.448 false 0.156,0.656 1.083,0.802 0.927,0.146 10 Vehicle Speed 1.51,2.104 1.719,2.302 0.208,0.198 10 [A] 2.167,1.656 2.396,1.823 0.229,0.167 10 [B] 3.188,1.646 3.396,1.802 0.208,0.156 10 [C] 3.823,3.01 4.031,3.167 0.208,0.156 10 [D] 4.677,0.854 4.906,1.052 0.229,0.198 10 [E] 5.656,1.615 5.854,1.813 0.198,0.198 10 [F] 6.375,3.021 6.615,3.208 0.24,0.188 10 [G] 0.667,1.75 1.052,1.938 0.385,0.188 10 Idling 4.813,0.26 6.292,0.625 1.479,0.365 10 There is no designated vehicle speed 0.208,2.031 1.135,2.344 0.927,0.313 10 Ignition Switch ON 1.906,2.5 2.698,2.833 0.792,0.333 10 Warming up the engine 2.74,2.521 3.896,2.688 1.156,0.167 10 5 minutes or more 5.271,2.531 6.427,2.698 1.156,0.167 10 5 minutes or more 4.125,2.563 5.021,2.729 0.896,0.167 10 2 to 3 minutes

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / EFI / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Idle the engine for 5 minutes or more [F].

12.

Enter the following menus: Powertrain / EFI / Trouble Codes [G].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0017)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.

HINT:

If any DTCs other than P0016 or P0017 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC P0016 or P0017 is output A
DTC P0016 or P0017 and other DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)

B

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the GTS or Techstream to the DLC3.


b.

Start the engine.


c.

Turn the A/C on.


d.

Turn the GTS or Techstream on.


e.

Enter the following menus: Powertrain / EFI / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 1) / All Data / VVT Change Angle #1, VVT Ex Chg Angle #1.


f.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0017)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0017)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the pending DTCs.


Result:
Result Proceed to
DTC P0016 or P0017 is output A
DTCs are not output B



A

B

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake or exhaust camshaft).

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CAMSHAFT>REMOVAL

HINT:

Replace the camshaft bearing cap oil hole gaskets (oil control valve filter) when removing the cylinder head cover sub-assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY



Result:
Proceed to
OK
NG



OK

7.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

7.INSPECT OIL CONTROL VALVE FILTER
A325183

a.

Remove the oil control valve filter.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0017)

NG

REPLACE OIL CONTROL VALVE FILTER

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0017)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the pending DTCs.


Result:
Result Proceed to
DTC P0016 or P0017 is output A
DTC is not output B



A

B