While the engine is being cranked, positive battery voltage is applied to terminal STSW of the ECM.
If the ECM detects the starter signal while the vehicle is being driven, it determines that there is a malfunction in the starter signal circuit. The ECM then illuminates the MIL and stores this DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0617 | Starter Relay Circuit High | All of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):
(a) The vehicle speed is 20 km/h (12.43 mph) or more. (b) The engine speed is 1000 rpm or higher. (c) The STA signal is on. |
·
Starter signal circuit ·
No. 1 integration relay ·
Ignition or starter switch assembly ·
ECM |
Comes on | DTC stored |
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON and turn the GTS or Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS or Techstream on [A].
Start the engine.
Idle the engine for 5 seconds or more [B].
Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / EFI / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
Inspect the fuses for circuits related to this system before performing the following procedure.
Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Data List / STA SW.
Check the value displayed on the GTS or Techstream when the vehicle is driven at 20 km/h (12.43 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
| Condition | STA SW | Proceed to |
|---|---|---|
| Driving at 20 km/h (12.43 mph) or more | OFF | A |
| ON | B |
A
B
Disconnect the ECM connector.
Disconnect the No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-60(STSW) or 1F-15 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (ST NO. 2 relay).
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E28-4(ST) - 1F-16 | Always | Below 1 Ω |
| E28-4(ST) or 1F-16 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>2NR-VE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0617 is output | A |
| DTCs are not output | B |
A
B