Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P2118  Throttle Actuator Power Supply Malfunction  


DESCRIPTION

The electronic throttle control system has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 5 V), the ECM determines that there is a malfunction in the electronic throttle control system and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the electronic throttle control system itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

The Electronic Throttle Control System (ETCS) does not use a throttle cable.


A361098E01
0.333,1 1.521,1.385 1.188,0.385 10 false to No. 1 Integration Relay 0.333,1.792 1.5,2.146 1.167,0.354 10 false to No. 1 Integration Relay 4.635,0.76 4.99,1.094 0.354,0.333 10 false +B1, +B2 4.615,1.688 5.073,1.885 0.458,0.198 10 false +BM 4.635,2.417 4.948,2.615 0.313,0.198 10 false M+ 4.635,3.073 4.948,3.271 0.313,0.198 10 false M- 4.625,3.74 5.24,3.938 0.615,0.198 10 false ME01 0.667,3.5 3.271,3.698 2.604,0.198 10 false Throttle Actuator 5.75,0.927 6.667,1.313 0.917,0.385 10 false Power Source Circuit for CPU 5.729,2.583 6.646,3.292 0.917,0.708 10 false Throttle Actuator Control Circuit 5.49,4.219 5.948,4.417 0.458,0.198 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2118 Throttle Actuator Power Supply Malfunction An open in the electronic throttle control system power source (+BM) circuit (1 trip detection logic).
·

Open in electronic throttle control system power source circuit

·

Battery

·

Battery terminals

·

No. 1 integration relay

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A199315E70
0.979,0.552 1.625,0.76 0.646,0.208 10 false 3000 rpm 1.24,1.927 1.625,2.146 0.385,0.219 10 false Idling 0.521,2.229 1.917,2.469 1.396,0.24 10 false Ignition Switch ON 3.146,2.208 4.719,2.344 1.573,0.135 10 false Approximately 5 seconds 3.469,2.802 4.792,2.99 1.323,0.188 10 false 16 seconds or more 2.01,2.313 2.208,2.542 0.198,0.229 10 false [A] 6.01,3.229 6.24,3.417 0.229,0.188 10 false [C] 4.604,0.417 4.833,0.604 0.229,0.188 10 false [B]

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Start the engine.

7.

Slowly depress the accelerator pedal, raise the engine speed to approximately 3000 rpm over approximately 5 seconds, and then idle the engine [B].

8.

Check that 16 seconds or more have elapsed since the engine was started.

9.

Enter the following menus: Powertrain / EFI / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle valve opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (+BM VOLTAGE)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / +BM voltage.


e.

Read the value displayed on the GTS or Techstream.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
2.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
a.
A360921C01
0.552,0.281 0.969,0.531 0.417,0.25 0.083,0.073 0.448,0.427 0.365,0.354 10 false *a 0.688,0.323 1,0.594 0.313,0.271 10 false 1F
*a Component with harness connected
(No. 1 Integration Relay)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1F-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM - BODY GROUND)

NG

4.INSPECT NO. 1 INTEGRATION RELAY (E-THRO RELAY)
3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1F-2 - A24-6(+BM) Always Below 1 Ω
1F-2 or A24-6(+BM) - Body ground Always 10 kΩ or higher
C50-3 (MR01) - Body ground Always Below 1 Ω
C50-105 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NO. 1 INTEGRATION RELAY (E-THRO RELAY)
a.

Inspect the No. 1 integration relay (E-THRO).

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (E-THRO RELAY) - POSITIVE BATTERY TERMINAL)

NG