A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil assembly. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.
The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.
Inspect the fuses for circuits related to this system before performing the following procedure.
| *a | Front view of wire harness connector
(to Ignition Coil Assembly) |
Disconnect the ignition coil assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C28-1 (+) - C28-4 (-) | Ignition switch ON | 11 to 14 V |
| C29-1 (+) - C29-4 (-) | Ignition switch ON | 11 to 14 V |
| C30-1 (+) - C30-4 (-) | Ignition switch ON | 11 to 14 V |
| C31-1 (+) - C31-4 (-) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition coil assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C28-4 (-) - Body ground | Always | Below 1 Ω |
| C29-4 (-) - Body ground | Always | Below 1 Ω |
| C30-4 (-) - Body ground | Always | Below 1 Ω |
| C31-4 (-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C28-3 (IGT) - C50-40 (IG1) | Always | Below 1 Ω |
| C29-3 (IGT) - C50-41 (IG2) | Always | Below 1 Ω |
| C30-3 (IGT) - C50-42 (IG3) | Always | Below 1 Ω |
| C31-3 (IGT) - C50-43 (IG4) | Always | Below 1 Ω |
| C28-3 (IGT) or C50-40 (IG1) - Body ground | Always | 10 kΩ or higher |
| C29-3 (IGT) or C50-41 (IG2) - Body ground | Always | 10 kΩ or higher |
| C30-3 (IGT) or C50-42 (IG3) - Body ground | Always | 10 kΩ or higher |
| C31-3 (IGT) or C50-43 (IG4) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel injector assembly connectors.
Disconnect the No. 1 integration relay (IG2 relay) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C28-1 (+) - 1D-5 | Always | Below 1 Ω |
| C29-1 (+) - 1D-5 | Always | Below 1 Ω |
| C30-1 (+) - 1D-5 | Always | Below 1 Ω |
| C31-1 (+) - 1D-5 | Always | Below 1 Ω |
| C28-1 (+) or 1D-5 - Body ground | Always | 10 kΩ or higher |
| C29-1 (+) or 1D-5 - Body ground | Always | 10 kΩ or higher |
| C30-1 (+) or 1D-5 - Body ground | Always | 10 kΩ or higher |
| C31-1 (+) or 1D-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (IG2 relay).
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG